Sawing With Special Base Runners; Sawing With The Angle Table; Transport; Sawing With The Adaptation Table - Festool CARVEX PSC 420 EB Manual De Instrucciones Original

GB PSC 420 EB
10.2

Sawing with special base runners

The special base runners protect high-quality sur-
faces against scratches and scores.

Press in the base runner at position [7-1].

At the same time, push the base runner for-
wards.

Mount another base runner and push it to the
rear until it engages.
10.3

Sawing with the angle table

The angle table WT-PS 400 is used for cutting pipes
or interior and exterior angles up to 45°.
Dust extraction is not possible when sawing
with the angle table!
Installing the angle table

Remove the saw base [1-10], (see chapter 7.4).

Position the angle table against the saw base
support.

Close the lever [1-8].
Ensure that the angle table is firmly seated in the
guide.
Setting the angle

Turn the adjusting wheel [8-1] to select the re-
quired angle.
You can select the angles -45°, 0° and +45° on the
scale [8-2] .
WARNING
Sawing cutting depths
Risk of injury

Select the saw blade length and cutting depth so
that the saw blade remains plunged in the work-
piece.

For 90° cuts, we recommend setting the angle
table to a small negative angle to guarantee
smooth operation.
10.4

Sawing with the adaptation table

The adaptation table ADT-PS 400 is used for fitting
your jigsaw on the Festool guide rail and the circle
cutter KS-PS 400.
With guide rail and circle cutter: do not ex-
ceed max. material thickness of 20 mm and
always use cross-set saw blades (FSG).
Installing the adaptation table

Remove the saw table [1-10], (see chapter 7.4).

Mount the adaptation table [9-1] on the saw ta-
ble support.
22
All manuals and user guides at all-guides.com

Ensure that the adaptation table is firmly seated in
the guide.

Adaptation to the guide rail FS 2
The Festool guide system FS 2 (Fig. [10]) makes it
much easier to manufacture straight precision
cuts.

Adaptation to the circle cutter
The circle cutter can be used to create circular cuts
with a diameter between 120 and 3000 mm. The cir-
cle cutter can be installed from both sides on the
adaptation table.



Recommended when using the circle cutter:





11
The lithium-ion batteries are subject to the require-
ments of the legislation on hazardous goods. A li-
ion battery pack alone falls below the applicable
limit value and certified as per UN manual ST/SG/
AC.10/11/rev. 3 part III, subsection 38.3. However,
dangerous goods regulations may apply when sev-
eral battery packs are transported For shipping by
third parties (e.g. air transport or freight forward-
ing company) special requirements with regard to
packaging and labelling must be observed.For the
preparation of the package an expert on hazardous
goods must be consulted. Please observe any fur-
ther national regulations.
Only return the battery pack if the housing is un-
damaged. Tape over the exposed contacts and wrap
the battery pack so that it cannot move inside the
packaging.
Close the change lever [1-8].
Use the extractor connector [1-7] also with the
adaptation table.
Place the jigsaw with attached adaptation table
[9-1] on the guide rail.
Place the jigsaw with attached adaptation table
on the adapter [11-1] on the circle cutter.
Insert the centring mandrel [11-2] in the hole
[11-4] on the circle cutter aligned with the saw
blade.
Clamp the measuring tape to the circle cutter
using the rotary knob [11-5].
Cut in an anticlockwise direction.
Work at a slow rate of advance.
Set the pendulum stroke [1-11] to 0 - 1.
Set the stroke rate [1-5] to 1 - 5.
Store the centring mandrel in the depot [11-3].

Transport