Smoke hollow DG850C Manual Del Usuario página 21

Operating Instructions
LP GAS CYLINDER (TANK) SPECIFICATIONS
The installation of this appliance must be in accordance with all applicable local codes, or the National Fuel Gas
Code ANSI Z223.1 NFPA 54.
When purchasing or exchanging a cylinder for your gas grill, it must be:
1. Constructed and marked in accordance with the specifications for LP gas cylinders of the U.S. Department of
Transportation (DOT), and
2. Provided with a listed over-filling prevention device (OPD), and
3. Provided with a cylinder connection device compatible with the connection for outdoor cooking appliance.
The cylinder must also be equipped with:
• A shut-off valve terminating in a Type 1 gas cylinder valve outlet.
• A Type 1 valve that prevents gas flow until a positive seal is obtained.
• An arrangement for vapor withdrawal.
• A collar to protect the cylinder shut-off valve.
• A safety relief device having direct communication with the vapor space of the cylinder.
• A listed over-filling prevention device (OPD).
BEFORE STORING YOUR GRILL:
• Ensure that the cylinder valve is fully closed.
• Clean all surfaces. Lightly coat the burners with cooking oil to prevent excess rusting.
• If storing the grill indoors, disconnect the LP tank and leave the LP tank OUTDOORS.
• Place dust cap on cylinder valve outlet whenever the cylinder is not in use. Only install the type of dust cap on the cylinder valve
outlet that is provided with the cylinder valve. Other types of caps or plugs may result in leakage of propane.
INSTALLING THE LP GAS CYLINDER (TANK) ONTO THE GRILL
1. Check that the cylinder valve is closed by turning the knob clockwise.
2. Place the cylinder into the tank support bracket on the bottom of the left brace.
Then place tank retention wire over cylinder handle and secure tightly.
3. Orient the cylinder such that the valve opening faces left side of grill and so that
the hose is not kinked or damaged.
4. Make sure tank sits securely in tank support bracket.
The LP Gas Cylinder must be a 20 pound cylinder and have a Type 1 Cylinder Valve Outlet
CONNECTING THE LP GAS CYLINDER (TANK) TO THE GRILL
Connector.
Handle the Cylinder with care - do not drop it.
1. Inspect the propane tank valve rubber seal for cracks, wear or deterioration prior to use. A
damaged rubber seal can cause a gas leak, possibly resulting in an explosion, fire or severe bodily
When you are not using the grill, the LP Gas Cylinder should be dis-
harm. Do not use a propane tank with a damaged rubber seal.
connected.
2. Attach or detach regulator to the LP gas cylinder only when cylinder is sitting in tank holder.
Connect the regulator and hand tighten firmly.
3. Check that the cylinder valve is closed by turning the knob clockwise.
Do a leak test each time you connect a LP Gas Cylinder and before
4. Check that the grill's burner control knobs are in the "OFF" positions.
5. Visually inspect the hose assembly prior to each use for evidence of damage, excess wear, or
lighting the grill.
deterioration. If found, replace the assembly before using your grill. Only the manufacturer's
Never use a match or lit flame to test for leaks.
supplied replacement should be used.
To test, prepare a weak solution of detergent and water. Spray or
6. Remove the protective plastic cap from the cylinder valve.
swab the solution onto the connection of the regulator to the LP Gas 7. Check that the hose does not contain kinks, does not contact sharp edges, and does not contact surfaces that may
become hot during use.
Cylinder valve, and on all the joints in the hose connections up to the burner valves (which
8. Hold regulator and insert the brass nipple into the LP cylinder valve outlet. Ensure that the device is centered properly.
MUST be closed in the "OFF" position).
9. Turn the large coupling nut clockwise by hand and tighten to a full stop. Take care not to cross thread the coupling nut
Open the LP Gas Cylinder valve, and watch for any bubbles to appear at all the connection
onto the cylinder valve. Do not use tools to tighten connection. Note: If you are unable to make the connection, repeat
Steps 7 and 8.
points. No bubbles indicate - All Clear!
If there are any bubbles, there is a leak which must be fixed.
Never obstruct the flow of combustion and ventilation air.
®
21