Before Use - Teac VRDS-25X Manual Del Usuario

Before Use

Read This Before Operating
O Choose the installation location of your
unit carefully. Avoid placing it in direct
sunlight or close to a source of heat.
Also avoid locations subject to
vibrations and excessive dust, heat,
cold or moisture. Keep away from such
sources that hum, such as transformers
or motors.
O Do not open the cabinet as this might
result in damage to the circuitry or
electrical shock. If a foreign object
should get into the set, contact your
dealer.
O Be sure not to handle discs with dirty
fingers. Never insert a disc which has a
crack on the surface.
O When removing the power plug from
the wall outlet, always pull directly on
the plug, never yank the cord.
O To keep the laser-pickup clean, do not
touch it, and do not forget to close the
disc tray.
O Do not attempt to clean the unit with
chemical solvents as this might damage
the finish. Use a clean, dry cloth.
O Keep this manual in a safe place for
future reference.
Beware of condensation
When the player (or a compact disc) is
moved from a cold to a warm place or
used after a sudden temperature
change, there is the danger of
condensation. Water vapor in the air
could condense on the mechanism or
the laser pickup. If droplets of water
form on these parts, correct playback
will be impossible because the laser
cannot read the information from the
disc correctly. To prevent this, if you
are going to use the player in a
condition where condensation could
occur, you should leave the player for
1 or 2 hours after plugging it into an AC
outlet depending on the amount of
condensation. If this is done, the
player will stabilize at the temperature
of its surroundings.
Handling the Discs
This unit has been designed specifically for
reproduction of compact discs bearing the
"˛ " mark. No other discs can be
reproduced.
O Always place the compact disc in the
disc tray with the label facing upward.
(Compact discs can be played only on
one side.)
O To remove a disc from its storage case,
press down on the center of the case
and lift the disc out, holding it carefully
by the edges.
How to remove the disc
How to hold the disc
O Fingerprints and dust should be
carefully wiped off the disc's recorded
surface with a soft cloth.
Wipe radially
O Do not use thinner, benzine or alcohol
as they damage the surface of the
disc's plastic surface.
O Discs should be returned to their cases
after use to avoid serious scratches
that could cause the laser pickup to
"skip."
O Do not expose discs to direct sunlight or
high humidity and temperature for
extended periods.
Long exposure to high temperatures
can warp the disc.
O Do not stick paper or write anything
with a ballpoint pen on the surface of
the label side.
_ 4 _
IMPORTANT (for U.K. Customers)
DO NOT cut off the mains plug from
this equipment. If the plug fitted is not
suitable for the power points in your
home or the cable is too short to reach
a power point, then obtain an
appropriate safety approved extension
lead or consult your dealer.
If nonetheless the mains plug is cut
off, remove the fuse and dispose of
the plug immediately, to avoid a
possible shock hazard by inadvertent
connection to the mains supply.
If this product is not provided with a
mains plug, or one has to be fitted, then
follow the instructions given below:
IMPORTANT. The wires in this mains
lead are coloured in accordance with
the following code:
GREEN-AND-YELLOW: EARTH
BLUE: NEUTRAL
BROWN: LIVE
WARNING: This apparatus must be
earthed.
As the colours of the wires in the mains
lead of this apparatus may not
correspond with the coloured markings
identifying the terminals in your plug
proceed as follows.
The wire which is coloured GREEN-
and-YELLOW must be connected to
the terminal in the plug which is
marked by the letter E or by the safety
earth symbol © or coloured GREEN or
GREEN-and-YELLOW.
The wire which is coloured BLUE must
be connected to the terminal which is
marked with the letter N or coloured
BLACK.
The wire which is coloured BROWN
must be connected to the terminal
which is marked with the letter L or
coloured RED.
When replacing the fuse only a
correctly rated approved type should
be used and be sure to re-fit the fuse
cover.
IF IN DOUBT — CONSULT A
COMPETENT ELECTRICIAN.