Main Components; Assembly Components; Discharge Chute Adjustment Handle; Handle Assembly - Stiga ST 4851 AE Uso Y Mantenimiento

Ocultar thumbs Ver también para ST 4851 AE:
Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 91
IMPORTANT Use the identification names
on the identification label of the product.
IMPORTANT Use these means of
identification whenever you contact
an authorized service workshop.
• IMPORTANT The example of the
Declaration of Conformity is provided
on the last pages of the manual.

3.4 MAIN COMPONENTS

The machine is made up of the 
following main components (fig. 1  ) :
A. Handle
B. Starter lever
C. Starter lever release
D. Chute adjustment handle
E. Led lights
F.
Handle pivot closure
G. Central handle
H. Ignition key
I.
Exhaust chute
J.
Deflector
K. Auger
L. Auger compartment
M. Wheel
N. Lower blade
O. Transport handle
Lower part of handle
P.
Q. Cable gland
R. Battery compartment
S. Battery charger (supplied separately)
T.
Battery (supplied separately)
4. ASSEMBLY
For storage and transport purposes, some 
components of the machine are not installed 
in the factory and have to be assembled after 
unpacking. Follow the instructions below.

4.1 ASSEMBLY COMPONENTS

The packaging holds the components needed 
for assembly (fig. 4  )  listed in the following table:
Component
Snow thrower
Discharge chute
adjustment handle
Handle
Handle fitting
Fig.
N.
4
1
4.A, 4.A1,
1
4.A2
4.B
1
4.C
1
EN - 7
Component
Spacers and screws for 
securing the handle in place
Spacers and screws for 
securing the handle in place
Ignition key
Cable gland to handle
Deflector
Instructions
4.2 UNPACKING
1. Cautiously  open  the  packaging,  paying 
attention not to lose components.
2. Consult  the  documentation  in  the  box, 
including these instructions.
3. Remove  all  the  unassembled  parts  from  the 
box.
4. Lift the snow thrower from the box.
5. Dispose  of  the  box  and  packaging  in 
compliance with local regulations.

4.3 HANDLE ASSEMBLY

1. Assemble  the  central  part  of  the  handle 
(fig.  4.C)  on  the  snow  thrower  (lower  part  of 
handle), fastening it with screws (fig. 4.D, 4.E) 
on both sides.
2. Position  the  upper  handle  (fig.  4.B)  on  the 
central  one  and  fasten  it  with  the  specific 
screws and fastenings (fig. 4.G, 4.F).
3. Fasten  the  electrical  cable  in  place  with  the 
specific cable gland (fig. 4.I).
4.4 DISCHARGE CHUTE ADJUSTMENT
HANDLE ASSEMBLY
1. Assemble  the  handle  (fig.  5.A1)  using  the 
specific  extension  shaft  (fig.  5.A),  fastening 
it in place with the 2 screws (fig. 5.A2).Make 
sure the holes of the shaft (fig. 5.A) and joint 
(fig. 5.A1) are aligned.
2. Insert the 2 screws in the holes and fix.
3. Pass the handle obtained in the specific lower 
handle support (fig. 5.B).
4. Insert  the  end  of  the  handle  in  the  specific 
coupling hole on the chute, keeping it straight 
and with the grip upwards (fig. 5.C).
5. Check  the  discharge  chute  by  turning  it 
entirely  in  both  directions.  The  chute  must 
freely rotate (fig. 9  ) .
4.5 DEFLECTOR ASSEMBLY
1. Insert  the  deflector  on  the  discharge  duct  in 
the upright position (fig. 6.A).
2. Fit the tabs on both sides in the rotation
eyelets (fig. 6.B).
Fig.
N.
4.D, 4.E
2
4.F, 4.G
4
4.H
1
4.I
1
4.J
1
-
1

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

St 8051 aeSt 515 liSt 615 li

Tabla de contenido