Troubleshooting Guide; Replacement Parts List - Good Earth Lighting SE1163-BP2-00LF0-G Manual Del Usuario

Installation For Round Surface Mount Electrical Boxes
AA/BB
GG x1
X2
FF x1
Pull supply wires out of the electrical box. Using machine screws (AA
or BB), secure mounting strap (FF) to the electrical box. Ensure the side
marked "FRONT" is facing out. Remove protective paper from adhesive
face of foam gasket (GG). Pull supply wires through the opening in
gasket and adhere gasket to the mounting strap and outer edge of
round surface electrical box.
DD x1
Fixture must be properly grounded. Connect fixture ground wire to
ground wire in electrical box using wire nut (DD). These wires can be
either green or bare copper. Insert black supply lead into connector
on black fixture wires and white supply lead into connector on white
fixture wires. Push excess wire into electrical box.
For Recessed Electrical Boxes
Silicone
Good Earth Lighting - 6 YEAR LIMITED WARRANTY
®
The manufacturer warrants this lighting fixture to be free from defects in materials and workmanship for a period of (6) years from the date of original purchase by the consumer. The
fixture is not warrantied for use in a commercial or retail application. The warranty is limited to use in a residential environment. We will repair or replace (at our option) the unit in the
original color and style if available, or in a similar color and style if the original item has been discontinued, without charge. Defective units must be properly packed and returned to
the manufacturer with a letter of explanation and your original purchase receipt showing date of purchase. Call 1-800-291-8838 to obtain a return authorization number and an address
where to ship your defective product. Note: C.O.D. shipments will NOT be accepted. The liability of the manufacturer is in any case limited to replacement of the defective light fixture
product. The manufacturer will not be liable for any other loss, damage, labor costs or injury which is caused by the product. This limitation upon the liability of the manufacturer
includes any loss, damage, labor costs or injury which is (I) to person or property or otherwise; (II) incidental or consequential in nature; (III) based upon theories of warranty,
contract, negligence, strict liability, tort, or otherwise; or (IV) directly, or indirectly related to the sale, use, or repair of the product. This warranty gives you specific rights, and you may
also have other rights which vary from state to state.

Troubleshooting Guide

Problem
Fixture doesn't light.
Fuse blows or circuit breaker trips
when light is turned on.
Good Earth Lighting is a registered trademark of Good Earth Lighting, Inc. All rights Reserved.
®
Good Earth Lighting® 1400 East Business Center Drive, Ste. 108 Mount Prospect, IL 60056
Printed in China
Before doing any work on the fixture, shut off power supply at the circuit breaker panel
to avoid electrical shock.
Cause
Power is off.
Bad connection.
Bad switch.
Discontinue use.
Installation For Recessed Electrical Boxes
AA/BB
X2
FF x1
Pull supply wires out of the electrical box. Using machine screws (AA
or BB), secure mounting strap (FF) to the electrical box. Ensure the
side marked "FRONT" is facing out.
FF x1
EE x1
Position fixture over the mounting strap. Secure long machine screw
(CC) through the center hole of the wall plate and mounting strap.
NOTE: Ensure gasket (GG) properly seals gap between wall plate and
electrical box to prevent water seepage into electrical box. Restore
power to the electrical box and ensure that the light is functioning
properly. If the light is functioning properly, fit the silicone cap (EE)
into the mounting screw opening to prevent water seepage into the
housing.
For recessed electrical boxes, use silicone adhesive caulking (not
included) to seal the gap between the wall plate and the mounting
surface to prevent water seepage into the electrical enclosure.
Solution
Check if power supply is on.
Check cords and/or wiring.
Test or replace switch.
Call customer service.

Replacement Parts List

Hardware Kit:
ZH-SE1163F03
SAVE THESE INSTRUCTIONS.
2