To connect a nozzle to the spray wand:
Turn off the pressure washer and shut off the water
supply. Pull trigger to release water pressure.
Engage the lock-out on the trigger handle by pushing up
on the lock-out until it clicks into the slot.
Pull back the quick-connect collar.
Push the nozzle into place in the spray wand.
Push the collar forward so that the nozzle is secured
properly. Check to see that the nozzle is secure.
To disconnect a nozzle from the spray wand once the
cleaning job is complete:
Turn off the pressure washer and shut off the water
supply. Pull trigger to release water pressure.
Engage the lock-out on the trigger handle by pushing up
on the lock-out until it clicks into the slot.
Pull back and hold the quick-connect collar.
Remove the nozzle by pulling it from the quick-connect
collar. Place nozzle in the nozzle storage area on the top
of the machine.
USING THE HIGH-PRESSURE HOSE
WARNING:
Injection hazard. Fully unwrap and straighten high
pressure hose prior to and during each use and do
not allow it to become kinked. The high pressure hose
features an outer covering that provides strength to the
hose. If the outer covering becomes damaged, stop using
the hose and replace it immediately. A kinked or damaged
hose can develop a high pressure leak and result in a
possible injection or other serious personal injury.
To prevent damage to the outer covering:
Inspect the hose before every use.
Fully unwrap and straighten hose before use.
Do not allow the high pressure hose to be kinked.
Keep hose away from hot surfaces and sharp edges.
Do not pull unit by high pressure hose.
Do not allow hose to be crushed or wrapped around
objects.
WASHING WITH DETERGENT
See Figures 16 - 17.
As sold, this unit is designed for use with "downstream"
pressure washer detergents. To convert for use with
"upstream" detergents, contact an authorized customer
service center for more information.
OPERATION
NOTICE:
USE ONLY DETERGENTS DESIGNED FOR PRESSURE
WASHERS. Do not use household detergents, acids,
alkalines, bleaches, solvents, flammable material, or
industrial grade solutions, which can damage the pump
or cause property damage. Many detergents may
require mixing prior to use. Prepare cleaning solution
as instructed on the solution bottle. Always test in an
inconspicuous area before beginning.
Disconnect pressure washer from power supply.
Pour detergent in the soap tank.
NOTE: Use a funnel, if needed, to prevent accidental
spilling of the detergent outside the tank. If any detergent
is spilled during the filling process, make sure the unit is
cleaned and dried before proceeding.
NOTE: The machine setting of this unit is 20:1, which usu-
ally allows the use of 1 gallon pressure washer detergent
without further dilution. Check your detergent instructions
to be sure additional dilution is not necessary.
Install the blue or black soap nozzle on the spray wand.
Connect unit to power supply and turn the pressure
washer on.
Squeeze the trigger and wait approximately 5 seconds
for the detergent to appear.
Spray the detergent on a dry surface using long, even,
overlapping strokes. To prevent streaking, do not allow
detergent to dry on the surface.
Before shutting off the motor:
Fill the soap tank with clean water.
Spray the clear water through the spray wand until the
tank is empty.
If any detergent remains in the spray, repeat with a second
tank of clean water.
Shut off the motor.
NOTE: Shutting off the motor will not relieve pressure in the
system. Pull trigger to release water pressure.
RINSING WITH THE PRESSURE WASHER
Turn off the pressure washer and shut off the water
supply. Pull trigger to release water pressure.
Engage the lock-out on the trigger handle by pushing up
on the lock-out until it clicks into the slot.
Remove the soap nozzle and place in the nozzle storage
area.
Select the right nozzle for the job. See the chart shown
earlier in the manual to select the appropriate nozzle.
Start at the top of the area to be rinsed and work down,
overlapping the strokes.
Page 13 — English