Trouble Shooting; Technical Data - Metabo KGS 216 M Manual De Instrucciones

ENGLISH

14. Trouble Shooting

This section describes problems and
malfunctions which you should be able
to resolve yourself. If the measures de-
scribed here do not solve your problem,
see 'Repairs'.
A
Danger!
Many accidents happen particularly in
connection with problems and faults.
Therefore please note the following:
Always unplug before troubleshooting.


15. Technical Data

Voltage
Current draw
Fuse protection
Motor capacity (S6 20% 5 min.)
Protection rating
Protection class
Saw blade speed
Cutting speed
Saw blade diameter (outer)
Arbor bore
Dimensions
Machine in packaging (length × width × height)
Machine ready for operation, rotating table in 90° position 
(length / width / height)
Maximum workpiece cross section:
Standard cross cuts
- Turntable 0°, rocker arm 0°
Mitre cuts
- Turntable 15° / rocker arm 0°
- Turntable 22,5° / rocker arm 0°
- Turntable 30° / rocker arm 0°
- Turntable 45° / rocker arm 0°
Bevel cuts
- Turntable 0°, rocker arm 45°
Compound mitre cuts
- Turntable 15° / rocker arm 45°
- Turntable 22,5° / rocker arm 45°
- Turntable 30° / rocker arm 45°
- Turntable 45° / rocker arm 45°
Weight
Machine in packing
Machine ready to work
Permissible temperature for transport and storage
Noise emission according to EN 61029-1
Sound power level L
WA
Sound pressure level at operator's ear L
Uncertainty K
Effective value of weighted acceleration according to EN 61029-1
(Vibration on handle) Vector sum a
Uncertainty K
Dust collector (not included in standard delivery):
Diameter of dust extraction port at rear of saw
Minimum air volume flow
Minimum vacuum at suction port
Minimum air speed at suction port
Laser guide:
Laser product class
Laser product standard
Max. output power P
Wave length
* The values stated are emission values and as such do not necessarily constitute values which are safe for the workplace. Although there is a correlation between emis-
sion levels and environmental impact levels, whether further precautions are necessary cannot be derived from this. Factors influencing the actually present environmen-
tal impact level in the workplace include the characteristics of the work area and other noise sources, i.e. the number of machines and other neighbouring work proc-
esses. The permitted workplace values can likewise vary from country to country. This information is intended to assist the user in his estimate of hazards and risks.
18
Check that all safety devices are oper-

ational again after each fault service.
No crosscut function
Transport locking pin engaged:
Pull transport locking pin out.

Safety lock engaged:
Release safety lock.

Sawing performance too low
Saw blade blunt (possibly tempering
marks on blade body):
Saw blade not suitable for material be-
ing cut (see section 'Technical Data');
Saw blade warped:
PA
h
Replace saw blade (see section

'Maintenance').
Saw vibrates heavily
Saw blade warped:
Replace saw blade (see section

'Maintenance').
Saw blade incorrectly mounted:
Remove the saw blade and then

mount it again correctly (see chapter
'Care and Maintenance').
Rotary table stiff
Sawdust build-up under rotary table:
Remove saw dust.

KGS 216 M
V 230 – 240 (1~ 50/60 Hz) 230 – 240 (1~ 50/60 Hz)
A 7
A 10 (time-lag)
kW 1.5
IP 20
II
-1
min 5000
m/s 55
mm 216
mm 30
mm 895 × 475 × 380
mm 820 × 543 × 355
width / height
mm 305 / 65
mm 295 / 65
mm 280 / 65
mm 260 / 65
mm 215 / 65
mm 305 / 36
mm 295 / 36
mm 280 / 36
mm 260 / 36
mm 215 / 36
kg 19
kg 14
°C 0 to +40
dB(A) 86.8
dB (A) 99,8
dB (A) 3,0
2
m/s < 2.5
2
m/s 1.5
mm 31.6
3
m /h 460
Pa 530
m/s 20
2
EN 60825-1: 1994 +A1 +A2
mW 1.0
nm 650
KGS 254 M
8,7
10 (time-lag)
1.8
20
II
4500
55
254
30
895 × 545 × 420
850 × 620 × 400
width / height
305 / 90
295 / 90
280 / 90
260 / 90
215 / 90
305 / 47
295 / 47
280 / 47
260 / 47
215 / 47
23
17,5
0 to +40
86.8
99,8
3,0
< 2.5
1.5
31.6
460
530
20
2
EN 60825-1: 1994 +A1 +A2
1.0
650