Maintenance And Servicing; Conformity Declaration - Rupes HR81M Instrucciones De Funcionamiento Y Mantenimiento

change.

MAINTENANCE AND SERVICING

WARNING: To reduce the risk of injury, turn unit off and disconnect it from power source (when machine is
connected to a power supply) or battery pack (when machine is connected to a battery pack) before installing and
removing accessories, before adjusting or when making repairs. Be sure the switch is in the "OFF" position. An
accidental start-up can cause injury. DANGER: The indicated measurements refer to new power tools. Daily usage causes the noise and vibration values to
change.
CLEANING
MAINTENANCE AND SERVICING At the end of each work session, or when required, remove any dust from the body of the tool using a soft cloth, paying
particular attention to the motor ventilation slots.. No other maintenance operations must be undertaken by the user.
WARNING: To reduce the risk of injury, turn unit off and disconnect it from power source (when machine is
LUBRICATION
connected to a power supply) or battery pack (when machine is connected to a battery pack) before installing and
This tool has been lubricated with a sufficient amount of high grade lubricant for the life of the unit under normal operating
removing accessories, before adjusting or when making repairs. Be sure the switch is in the "OFF" position. An
conditions. No further lubrication is necessary.
accidental start-up can cause injury.
REPAIRS
CLEANING
Maintenance and cleaning of the inner parts like ball bearings, gears etc. or others, must be carried out only by an authorized
At the end of each work session, or when required, remove any dust from the body of the tool using a soft cloth, paying
customer service workshop.
particular attention to the motor ventilation slots.. No other maintenance operations must be undertaken by the user.
DISPOSAL (WEEE DIRECTIVE)
LUBRICATION
FOR EC COUNTRIES ONLY: According to the European Directive on Waste from electrical and electronic
This tool has been lubricated with a sufficient amount of high grade lubricant for the life of the unit under normal operating
equipment and its implementation in conformity with national standards, exhausted electrical equipment must be
conditions. No further lubrication is necessary.
collected separately, in order to be recycled in an environmentally friendly way. The product, when it reaches the end
REPAIRS
of its life, must not be dispersed in the environment or thrown away as household waste. It must be disposed at
Maintenance and cleaning of the inner parts like ball bearings, gears etc. or others, must be carried out only by an authorized
authorized recycling centres.
customer service workshop.
Rupes BIGFOOT NANO Hybrid tool Part Numbers:
DISPOSAL (WEEE DIRECTIVE)
HR81M - short neck Rupes BIGFOOT NANO Hybrid tool
FOR EC COUNTRIES ONLY: According to the European Directive on Waste from electrical and electronic
HR81ML - long neck Rupes BIGFOOT NANO Hybrid tool
equipment and its implementation in conformity with national standards, exhausted electrical equipment must be
9HC120LT Li-ION Battery Charger
collected separately, in order to be recycled in an environmentally friendly way. The product, when it reaches the end
9HB120LT Li-ION Battery pack
of its life, must not be dispersed in the environment or thrown away as household waste. It must be disposed at
9HP120LT Rupes BIGFOOT NANO Hybrid tool Power Supply
authorized recycling centres.

CONFORMITY DECLARATION

Rupes BIGFOOT NANO Hybrid tool Part Numbers:
We declare on our responsibility that the represented tool is in conformity with the directives:
2006/42/EC; 2014/35/EU; 2004/108/EC; 2011/65/EU.
HR81M - short neck Rupes BIGFOOT NANO Hybrid tool
EN 60745-1: 2009+A11 2010;
HR81ML - long neck Rupes BIGFOOT NANO Hybrid tool
EN 60745-2-3: 2011+A12 2014+A13 2015;
9HC120LT Li-ION Battery Charger
EN 60745-2-4: 2009+A11 2011;
9HB120LT Li-ION Battery pack
EN 55014-1: 2006+A1 2008;
9HP120LT Rupes BIGFOOT NANO Hybrid tool Power Supply
EN 55014-2: 1997+A1 2001+A2 2008;
EN 61000-3-2: 2007+A1 2009+A2 2009;
CONFORMITY DECLARATION
EN 61000-3-3: 2008;
We declare on our responsibility that the represented tool is in conformity with the directives:
EN 62233: 2008;
2006/42/EC; 2014/35/EU; 2004/108/EC; 2011/65/EU.
EN 60745-1: 2009+A11 2010;
EN 60745-2-3: 2011+A12 2014+A13 2015;
EN 60745-2-4: 2009+A11 2011;
EN 55014-1: 2006+A1 2008;
EN 55014-2: 1997+A1 2001+A2 2008;
EN 61000-3-2: 2007+A1 2009+A2 2009;
EN 61000-3-3: 2008;
EN 62233: 2008;
12
The tests have been carried out in accordance with standard:
The tests have been carried out in accordance with standard:
Vermezzo (MI), 03/13/2016
Technical file at:
RUPES SpA
Via Marconi, 3A
20080 - Vermezzo (MI) - Italy
Vermezzo (MI), 03/13/2016
Technical file at:
RUPES SpA
Via Marconi, 3A
20080 - Vermezzo (MI) - Italy
S
T
T
T
D
T
C
D
c
R
I
D
P
* 2
mi
La
uti
lus
**
AV
Le
qu
re
B
PO
• C
ins
tou
• C
les
• L
l'a
• L
de
• L
av
•
mo