Technical Specifications; Correct Usage - Rupes HR81M Instrucciones De Funcionamiento Y Mantenimiento

ENGLISH
Li-Ion
Wh
N0

TECHNICAL SPECIFICATIONS

TYPE
Voltage (VDC)
RPM
Battery life (min)
Charging time (min)
Electronic speed control
Overcurrent protection
Soft start
LED indication
Dimensions (mm)
Weight (g)
*
2000 RPM when speed regulation Knob (2) is at position 1, 2800RPM at position 2, 3500RPM at position 3, 4300RPM at
position 4, 5000 RPM at position 5.
* The value is referred to a use of the battery pack 9HB120LT, fully charged with a charger 9HC120LT and normal use with a
Rupes polishers HR81M/HR81ML and functional unit orbit 12mm and Ø30mm buffer pad.
** measured without a functional unit, battery pack, and power supply
WARNINGS
The safety and accident prevention instructions are reported in the "SAFETY INSTRUCTION" booklet which is an integral
part of these documents. This operating instructions manual indicates the additional information required for the specific
use of the tool.

CORRECT USAGE

CAUTION: DO NOT PUSH SHAFT LOCKING BUTTON (6) DURING USE! PUSH THE BUTTON ONL Y WHEN THE
SWITCH (2) IS IN OFF POSITION
• This tool is designed to be used as a polisher, sander, cleaner, brusher. Read all the warnings, instructions,
indications provided on drawings and specifications supplied with this tool. Failure to comply with all the instructions
provided below may cause electrical shocks, fire and/or serious injuries.
• This tool is not intended to be used for, metal brushing and cutting operations. The use of this tool for unintended
applications may cause hazards and injuries to people.
• The tool must be used with accessories that have been specifically designed or recommended by the manufacturer.
The fixing of the accessory to the tool does not guarantee a safe operation.
• The rated speed of the accessories must be at least equivalent to the maximum speed specified on the tool. Using
the accessories at speeds above the rated one, may cause them to break or thrown into the air.
• The external diameter and thickness of the accessories must match the specifications of the tool. Accessories with
incorrect dimensions cannot be adequately protected or controlled.
• The configuration of accessories must match the tool. The use of accessories that cannot be perfectly fitted on the tool
may result in imbalance, excessive vibrations and in the impossibility of controlling the tool. Do not use damaged
accessories. Before use, inspect all the accessories. Inspect the supporting pads and verify there are no cracks,
tears or excessive wear. If the tool or accessory has fallen, verify that it is not damaged or install a new accessory.
After inspecting or installing an accessory, test the operation of the tool at maximum speed and without load for one
minute, keeping at a safety distance. If the accessories are damaged, they will break during this test.
8
Summary of device labels containing safety information
WARNING: To reduce the risk of injury, user must read instruction manual
CE mark for EU market
Wear ear protection
Wear eye protection
WEEE Compliant
Product contains Lithium-Ion. Do not dispose this product with household rubbish
Watt per hour
No-load speed
Arrow – act in the direction indicated by the arrow direction
HR81M
10.8/12
2000-5000*
~30**
287x70x47***
470***
Ah
V
/min
~20
•
•
•
•
Direct current
Wear a gloves
Wear a mask
Ampere per hour
Volt
Per minute
HR81ML
10.8/12
2000-5000*
~30**
~20
•
•
•
•
332x70x47***
520***
• W
gla
ab
op
ex
• K
pr
of
• H
ma
po
• A
sp
• U
oth
as
• P
arm
• N
su
• A
de
co
• D
clo
• R
ac
• D
• D
PR
Th
PA
1 -
2 -
3 -
4 -
5 -
6 -
MO
(op
Th
pro
SW
To
the
To
EL
Th
ind
Sp
Th
Th
Ba
Th
NO
tur
Ba
Th