Description Of The Hood; Control Panel - ELICA Space EDS Montaje Y Modo De Empleo

Installation with flue
1. Use a pencil to mark the line representing the centre of
the appliance on the wall, as far as the ceiling. This will
make the installation process easier.
2. Position the drilling template on the wall: the vertical
centre line printed on the template should be aligned with
the centre line marked on the wall, and the lower edge of
the template should line up with the lower edge of the
cooker hood.
3. Rest the lower support bracket on the drilling template,
making sure it coincides with the sketched rectangle,
then mark the two outer holes and drill them.
Note: Always make the holes indicated on the template:
the 2 upper holes are used to position the hood, while the
lower holes (generally 1 central or several at the sides)
are used to fix it in place and secure it properly.
Remove the drilling template, insert the rawl plugs and fix
the cooker hood support bracket in place using 2 screws
measuring 5x45 mm.
4. Place the flue support bracket "G" on the wall so that it is
against the ceiling, use the flue support bracket as a
drilling template (if present, the small slot on the support
should coincide with the line made previously on the wall)
and use a pencil to mark 2 holes, then drill them (Ø 8
mm) and insert 2 rawl plugs.
5. Fix the flue support bracket to the wall using 2 screws
measuring 5x45 mm.
6. Hang the cooker hood on the lower bracket.
7. Adjust the distance between the cooker hood and the
wall.
8. Adjust the horizontal position of the cooker hood.
9. Fix the cooker
(COMPULSORY!!).
10. Connect a tube (tube and fixing clamps not supplied;
these are to be purchased separately) for the expulsion
of smoke to the connection ring located above the
suction motor assembly.
The other end of the tube should be connected to a
device for the expulsion of smoke outdoors if the cooker
hood is to be used as a ducted version. If you wish to use
the cooker hood as a filter version, fix deflector F to flue
support bracket G and connect the other end of the tube
to the connection ring located under deflector F.
11. Perform all necessary electrical connections.
12. Position the flue.
13. Fix the flue to the flue support bracket G using 2 screws.
14. Slot the front panel in and perform the necessary
electrical connections for the control panel.
15. Fix the front panel in place using 6 screws (3 per side).
16. Slot in the side panels and fix them in place by sliding
them downwards.
17. Position the upper fixing bracket and secure it using 2
screws.
Remount the carbon filter frame and the fat/s filter/s and check
the perfect functioning of the hood.
All manuals and user guides at all-guides.com
hood to the wall

Description of the hood

Fig. 1

1. Control panel

2. Grease filter
3. Grease filter release handle
4. Halogen lamp
5. Vapour catcher
6. Telescopic chimney
7. Air outlet (used for filter version only)
8. Panel
Operation
Use the high suction speed in cases of concentrated kitchen
vapours. It is recommended that the cooker hood suction is
switched on for 5 minutes prior to cooking and to leave in
operation during cooking and for another 15 minutes
approximately after terminating cooking.
Control panel
1. Lights ON/OFF Key: press and release to turn the lights
on and off at the preset intensity; keep pressed to adjust
the intensity of the light.
2. ON(Stand by)/OFF suction Key
-ON (Stand by) – the Key is on.
-OFF - the Key is off: all the commands with the
exception of key 1 are disenabled.
To set the hood on ON (stand by) or OFF press the key
and wait until the key lights up or turns off on the basis of
the setting desired.
securely
3. Speed (power) suction selection key 1: press once to
select the suction speed (power), press again and keep it
pressed to activate 20 minute (flashing key) functioning
time, after which the hood turns off (Stand by)
4. Speed (power) suction selection key 2: press once to
select the suction speed (power), press again and keep it
pressed to activate 15 minute (flashing key) functioning
time, after which the hood turns off (Stand by)
5. Speed (power) suction selection key 3: press once to
select the suction speed (power), press again and keep it
pressed to activate 10 minute (flashing key) functioning
time, after which the hood turns off (Stand by).
6. Intensive suction speed (power) ON/OFF selection
key (timed): press to select the suction speed (power).
Functioning time is 5 minutes after which suction turns off
or returns to the speed (power) previously selected.
7. COMFORT button: the hood begins to operate in a
"cyclical" manner when filtering the air, which means the
motor is activated at speed level 1 for 5 minutes and then
switched OFF for 30 minutes. This operating mode
remains set until the OFF button (or any of the speed
buttons) is pressed; this will stop the COMFORT function
and activate the motor at the selected speed level.
17