EBARA E-SPD+ Manual De Instrucciones Y Mantenimento página 32

Par. Description Units
5.18 DIGITAL INPUT 1
5.19 PRESSURE IN 1
5.20 SPEED IN 1
5.21 TEMPERATURE IN 1
5.22 DIGITAL INPUT 2
5.23 PRESSURE IN 2
5.24 SPEED IN 2
5.25 TEMPERATURE IN 2
5.26 DIGITAL INPUT 3
5.27 PRESSURE IN 3
5.28 SPEED IN 3
5.29 TEMPERATURE IN 3
5.30 DIGITAL INPUT 4
5.31 PRESSURE IN 4
5.32 SPEED IN 4
5.33 TEMPERATURE IN 4
SLAVE 1V
5.35
PRESSURE SETPOINT
SLAVE 9V
5.36
PRESSURE SETPOINT
SLAVE 1V
5.37
SPEED SETPOINT
SLAVE 9V
5.38
SPEED SETPOINT
SLAVE 1V
5.39
TEMPERATURE SETPOINT
SLAVE 9V
5.40
TEMPERATURE SETPOINT
Programming
Default Min.
Not used
Total Stop
Total Stop INV
Local Stop
Local Stop INV
Not used
IN Setpoint
IN Setpoint INV
Flow Sensor
Flow Sensor INV
Slave 0-10V
Bar 4 0,5
Hz 25 10
ºC -100
Not used See parameter 5.18
Bar 4 0,5
Hz 25 10
ºC -100
Not used See parameter 5.18
Bar 4 0,5
Hz 25 10
ºC -100
Not used See parameter 5.18
Bar 4 0,5
Hz 25 10
ºC -100
Bar Par 1,1 0,5
Bar Par 1,1 0,5
Hz 25 25
Hz 25 25
ºC 50 Par. 5.06
ºC 50 Par. 5.06
Max.
Selecting "Not used" will not affect the system.
We can use the digital input as a system start-stop or
only one pump start-stop choosing the Total Stop or Local
Stop options.
It can also be used as a different default set pressure in
the same way. Choosing IN Setpoint you can be select
another different set pressure on parameter 5.19.
Flow Sensor option is used when a flow sensor is
available, which will stop the pump.
Slave 0-10V option is used if a 0-10V active device or
a potentiometer (passive device) is connected to the
0-10V input.
Note: INV options are used for NC inputs.
FS
65 A different setpoint can be set if the input is active.
200
See parameter 5.18
FS
65 A different setpoint can be set if the input is active.
200
See parameter 5.18
FS
65 A different setpoint can be set if the input is active.
200
See parameter 5.18
FS
65 A different setpoint can be set if the input is active.
200
If a 0-10V device is installed, here you can set the
pressure value for the 1 volt signal.
Par. 5.05
*This parameter is available when any of the digital
input is set to Slave 0-10V.
If a 0-10V device is installed, here you can set the
pressure value for the 9 volt signal.
Par. 5.05
*This parameter is available when any of the digital
input is set to Slave 0-10V.
If a 0-10V device is installed, here you can set the speed
value for the 1 volt signal.
65
*This parameter is available when any of the digital
input is set to Slave 0-10V.
If a 0-10V device is installed, here you can set the speed
value for the 9 volt signal.
65
*This parameter is available when any of the digital
input is set to Slave 0-10V.
If a 0-10V device is installed, here you can set the
temperature value for the 1 volt signal.
Par. 5.07
*This parameter is available when any of the digital
input is set to Slave 0-10V.
If a 0-10V device is installed, here you can set the
temperature value for the 9 volt signal.
Par. 5.07
*This parameter is available when any of the digital
input is set to Slave 0-10V.
32
Notes
A
X
X
X
X
X
X
X
X
X
X
EN
Application
B C D E
X X X X
X
X
X X
X X X X
X
X
X X
X X X X
X
X
X X
X X X X
X
X
X X
X
X
X
X
X X
X X