Symbols And Meanings; General Safety Information For Power Tools - wolfcraft MASTER cut 2200 Traducción Del Manual De Instrucciones Original

GENERAL INFORMATION
INTRODUCTION
WARNING
In addition to this manual, also observe all the safety information, instruc-
tions, illustrations and technical data that were supplied with the power
tools used. Failure to comply with the instructions can lead to electric shock,
fire and/or serious injury.
Keep the operating instructions in a safe place for future reference.
These operating instructions describe the MASTER cut 2200 machine table (here-
after also referred to as "Product" or •"Table").
The purpose of the figures in this operating manual is to help you better under-
stand the topics and step sequences. The representations in the figures are ex-
amples and may deviate slightly from the actual appearance of your product.
The term "power tool" used in the safety information refers to electric tools oper-
ated with mains power (with mains power cable).

SYMBOLS AND MEANINGS

WARNING
WARNING
...means that there is risk of severe to life-threatening injury.
CAUTION
CAUTION
...means that there is risk of minor to moderate injury.
NOTICE
NOTICE
...indicates important information (e.g. risk of property damage), but not hazards.
Information
This symbol indicates information that helps you to quickly and safely
perform your tasks.
Warning of a danger
This symbol indicates a general hazard that, if not avoided, could res-
ult in injury.
Observe instructions!
This symbol indicates that the operating instructions must be followed.
Wear safety goggles!
This symbol indicates that you have to wear safety goggles.
Wear ear protection!
This symbol indicates that you have to wear ear protection.
Wear protective mask
This symbol indicates that you have to wear a protective mask.
Disconnect mains plug
Pull the plug when the device is not in use.
Do not use the table for cutting firewood.
Use only circular handsaws with a max. cutting depth of 70 mm.
EN Use only circular handsaws with a max. saw blade diameter of 200
mm.
Before each cut, adjust the cutting depth of your circular handsaw so
that the circular saw blade protrudes max. 4 mm out of the workpiece.
Use only circular handsaws with an integrated riving
knife.
Use as a milling table only in conjunction with the parallel
milling guide (art. no. 6901000).
Use only machines with a max. power of 2760 W.
Do not cut more than 5 mm into the worktop.
Do not sit on the table.
Do not stand on the table.
Do not apply weight to the table unevenly.
Do not apply a load of more than 120 kg to the table.
SAFETY

GENERAL SAFETY INFORMATION FOR POWER TOOLS

Workplace safety
– Keep your work area clean and well lit. Untidy or dark work areas can lead
to accidents.
– Do not use power tools in explosive atmospheres that contain flam-
mable liquids, gases or dusts. Power tools generate sparks that can ignite
dust or vapours.
– Keep children and other persons at a safe distance when using the
power tool. If you are distracted, you may lose control of the power tool.
Electrical safety
– The plug of the power tool must fit into the socket. The plug must not
be tampered with in any way. Do not use adapter plugs together with
earthed power tools. Unmodified plugs and matching sockets reduce the
risk of electric shock.
– Avoid making physical contact with earthed surfaces such as pipes,
heaters, cookers and refrigerators. There is increased risk of electric shock
when your body is earthed.
– Keep power tools out of the rain and away from wet environments. Wa-
ter penetrating into a power tool increases the risk of electric shock.
– Do not abuse the cord. Never use the cord for carrying, pulling or un-
plugging the power tool. Keep cord away from heat, oil, sharp edges
and moving parts. Damaged or entangled cords increase the risk of electric
shock
– When working with a power tool outside, use only extension cords that
are suitable for outdoor use. Using an extension cord that is suitable for
outdoor use reduces the risk of electric shock.
– If it is unavoidable to use a power tool in a wet environment, use a re-
sidual-current circuit breaker. It will reduce the risk of electric shock.
42