Personal Safety - wolfcraft MASTER cut 2200 Traducción Del Manual De Instrucciones Original

Personal safety

– Stay alert, watch what you are doing and use common sense when op-
erating a power tool. Do not use a power tool if you are tired or under
the influence of drugs, alcohol or medication. A moment of inattention
when using the power tool may result result in serious injuries.
– Use personal protective equipment and always wear eye protection.
Wearing protective equipment such as a dust mask, non-skid safety shoes,
hard hat or hearing protection as appropriate for the type of power tool and
its application reduces the risk of personal injuries.
– Prevent unintentional starting. Ensure that the power switch of the
power tool is in the OFF position before connecting to the power source
and/or battery pack, picking up or carrying the tool. Carrying power tools
with your finger on the switch or energising power tools that have the switch
on invites accidents.
– Remove the adjusting tools or spanners before switching on the power
tool. A tool or spanner left in a rotating part of the power tool can cause in-
jury.
– Avoid working with an abnormal posture. Ensure that you have secure
footing and proper balance at all times. This enables you to better control
the power tool in unexpected situations.
– Wear suitable clothing. Never wear loose clothing or jewellery. Keep
hair and clothing away from moving parts. Loose clothing, jewellery or
long hair can get caught in moving parts.
– If the design of the power tool allows for the connection of dust extrac-
tion and collection equipment, these have to be connected and properly
used. Using dust extraction equipment can reduce hazards posed by dust.
– Even if you are very familiar with the power tool from frequent use, do
not fall into the trap of a false sense of safety and do not disobey the
safety rules for using power tools. Careless action can cause severe injury
within fractions of a second.
Power tool use and care
– Do not force the power tool. Use the correct power tool for your task.
You will be able to do the work better and more safely when using the correct
power tool, in compliance with its rating.
– Do not use a power tool with a defective switch. A power tool that cannot
be switched on or off is dangerous and has to be repaired.
– Disconnect the plug from the electric socket and/or remove the battery,
if detachable, from the power tool before adjusting the tool, changing
accessories or storing the power tool. This precautionary measure prevents
the power tool from being started accidentally.
– When not in use, store power tools out of reach of children. Do not al-
low persons who are unfamiliar with the power tool or these instruc-
tions to use the power tool. Power tools are dangerous if used by inexperi-
enced persons.
– Maintain power tools and accessories with great care. Check that mov-
ing parts are working properly and no binding occurs; check for parts
that are broken or damaged such that the function of the power tool is
affected. Have damaged parts repaired before using the power tool.
Many accidents are the result of poorly maintained power tools.
– Keep cutting tools sharp and clean. Diligently maintained cutting tools with
sharp cutting edges are less likely to bind and easier to control.
– Use power tools, accessories, attachments etc. in accordance with these
instructions. Take the work conditions and the task to be performed into
account. Using power tools for applications other than the intended use can
result in hazardous situations.
– Keep handles and grasping surfaces dry, clean and free of oil and
grease. When handles and grasping surfaces are slippery, it is not possible to
ensure safe operation and control of the power tool in unexpected situations.
Service
– Have your power tool repaired only by qualified specialists, using only
original replacement parts. This ensures the power tool remains safe to use.
GENERAL SAFETY INFORMATION FOR THE MACHINE TABLE
– Correctly assemble and set up the machine table before installing the power
tool. Correct assembly and setup is important to prevent the table from col-
lapsing.
– Fasten the power tool securely to the machine plate before using it. If the
power tool slips on the machine plate, loss of control can result.
– Place the machine table on a firm, level and horizontal surface. If the machine
table can slip or wobble, the power tool or workpiece cannot be controlled
evenly and safely.
– Avoid overloading the machine table and never use it as a ladder or support.
Placing excess weight on the machine table or standing on it can cause the
centre of gravity of the table to shift upward, causing it to tip over.
– Do not use the tool on materials other than wood or easily machined plastics.
Exception: With the jigsaw only, it is permitted to cut easily machined metal
(such as aluminium), provided that a suitable saw blade is used.
– Do not remove loose fragments, chips or similar materials from the area
around the moving saw blade by hand.
– The machines used must comply with DIN EN 62841-1. Devices manufactured
after 1995 must bear a CE mark.
– Do not use the saw "freehand" - in other words, do not guide the workpiece
by hand only, but also use the parallel guide or angle stop.
– Take care not to pinch your hands when folding up and unfolding the ma-
chine table or inserting the machine plate.
– Before each sawing or routing operation, make sure that there are no objects
on the worktop.
– Do not stop the saw blades by applying lateral pressure after switching off the
drive.
– Only use tools for their actual intended purpose.
– Use only saw blades that are in perfect condition; the body of the saw blade
must be thinner and the tooth set must be wider than the thickness of the riv-
ing knife.
– Regularly check that all screws are securely fastened.
– Never use your machine table improperly or for an unintended purpose.
– Remove all unnecessary items from the machine table.
– Do not use the table for cutting firewood.
– Do not use the machine table for cutting round pieces of wood.
– Use only the safety switch to switch the power tools on and off.
– To permanently fix the power tool's switch in the ON position, use only the
supplied switch clamp.
– Replace damaged gap inserts with new ones.
– When working with narrow workpieces, always use a push stick.
– Make sure the eccentric levers for fixing the table legs in position are closed
and tightened. If necessary, retighten the eccentric levers.
– Before starting to work, make sure that the circular handsaw, the router or
the jigsaw is properly attached to the machine plate.
– Observe the maximum permitted workpiece dimensions (see Technical Data).
– Use the various gap inserts exclusively for their respective intended purpose,
as graphically depicted on each gap insert.
– When not in use, hang the push stick, the gap inserts or the angle stop on the
screw hooks provided for this purpose.
– Do not use the machine table outdoors in the rain or in damp conditions.
– Before starting to work, make sure that the screws used to mount the ma-
chine plate to the machine table have been securely tightened.
– Make sure that you use the appropriate gap insert for the respective machine.
– CAUTION There is a risk of tipping when using protruding workpieces. Make
sure that lateral clamping and machining of laterally clamped workpieces
does not result in the machine table becoming unbalanced.
– Make sure that you do not apply excessive clamping pressure when fastening
fragile materials. Risk of splinters
– Place heavy objects on the machine table with care and ensure an even load
on the tabletop.
– Do not saw more than 5 mm into the machine table as this will damage the
aluminium profile.
– Be careful when inserting and removing the machine plate: there is risk of
crush and cut injuries.
– For transport, make sure the legs have been correctly locked in place under-
neath the machine table and have been fixed in position with the hook and
loop straps.
– Before transporting the machine table, remove all loose parts that cannot
safety be fastened to it.
– Do not carry the folded machine table on one side by the legs, but instead
use two hands to hold it at the right and left on the aluminium profile.
43