Fuel Mixture Chart; Mixing Instructions; Starting And Stopping - Maruyama P23-10 Manual Del Operador

oils may lead to service issues which may Not be
low-emission air-cooled 2-cycle engines. Use of other
covered by your warranty.
oils may lead to service issues which may Not be
covered by your warranty.
Fuel Mixture
Fuel Mixture
The fuel: oil ratio is 50 parts gasoline to 1 part oil or 50:1.
The fuel: oil ratio is 50 parts gasoline to 1 part oil or 50:1.
Note: Never use a mixing ratio less than 50:1
regardless of the oil package mixing
Note: Never use a mixing ratio less than 50:1
instructions. Ratios less than 50:1,
regardless of the oil package mixing
(for example, 60:1, 80:1, 100:1), reduce
instructions. Ratios less than 50:1,
the amount of lubrication to the internal
(for example, 60:1, 80:1, 100:1), reduce
moving parts of the engine and can cause
the amount of lubrication to the internal
damage.
moving parts of the engine and can cause
damage.

Fuel Mixture Chart

Mixing Instructions

IMPORTANT: Never mix gasoline and oil
directly in the Pruner fuel tank.
1. Always mix fuel and oil in a clean container
approved for gasoline.
2. Mark the container to identify it as fuel mix for
the Pruner.
3. Use regular unleaded gasoline and fill the container
with half the required amount of gasoline.
4. Pour the correct amount of oil into the container
then add the remaining amount of gasoline.
5. Close the container tightly and shake it momentarily
to evenly mix the oil and the gasoline before
filling the fuel tank on the Pruner.
6. When refilling the Pruner fuel tank, clean around the
fuel tank cap to prevent dirt and debris
from entering the tank during cap removal.
7. Always shake the premix fuel container momen-
tarily before filling the fuel tank.
8. Always use a spout or funnel when fueling to
6. When refilling the Pruner fuel tank, clean around the
from entering the tank during cap removal.
fuel tank cap to prevent dirt and debris
from entering the tank during cap removal.
7. Always shake the premix fuel container momen-
tarily before filling the fuel tank.
7. Always shake the premix fuel container momen-
tarily before filling the fuel tank.
8. Always use a spout or funnel when fueling to
reduce fuel spillage.
8. Always use a spout or funnel when fueling to
reduce fuel spillage.
9. Fill the tank only to within 1/4-1/2 inch (6 mm-13
mm) from the top of the tank. Avoid filling to the
9. Fill the tank only to within 1/4-1/2 inch (6 mm-13
top of the tank filler neck.
mm) from the top of the tank. Avoid filling to the
top of the tank filler neck.

Starting And Stopping

Before Starting The Engine
1. Fill the fuel tank as instructed in the Before Operation
section of this manual (page US-14).
2. Rest the Pruner on the ground.
3. Make sure the cutting attachment is clear of any
broken glass, nails, wire, rocks or other debris.
4. Keep all bystanders, children and animals away
from the working area.
Cold Starting Procedure
This Pruner is equipped with a fuel primer and a
choke system. To start a "cold" engine properly, perform
the following procedure:
1. Pump the primer bulb at the bottom of the carbu-
retor until fuel can be seen flowing through the
fuel return line to the fuel tank.
(Flowing fuel should be almost clear, not foamy or
full of bubbles.)
2. Move the choke lever to the closed (
and move the stop switch to the "ON" position.
− US-17 −
3. L
po
• D
• D
4. A
thr
mo
If
ch
A.
B.
C.
Hot
) position
To st
resta
(20°C
1. P
bur
fue
Fa
p