Ethernet Receiver 1 Options; Ethernet Receiver 2 Options; Ethernet Options - DSC TL260 Manual De Instrucciones

Alternate Test Transmission can be enabled or disabled in Section [005] Toggle Option [7]. When the toggle is ON, test transmissions
alternate between the receivers at the test transmission interval.
[026] Ethernet 1 Transmission
Default (FF);
Program 00 to disable this event transmission or FF to enable. See System Test Options (above) for details on settings.
[027] Ethernet 2 Transmission
Default (00);
Program 00 to disable this event transmission or FF to enable. See System Test Options (above) for details on settings.
[030] FTC Restore
Default (FF);
Program 00 to disable this event transmission or FF to enable. This event will occur when an FTC Trouble on the system restores.

Ethernet Receiver 1 Options

[101] Ethernet Receiver 1 Account Code
Default (0000000000);
The account code is used by the central station to distinguish between transmitters. It is used when transmitting heartbeat signals to the
central station receiver. Signals received from the Control Panel will use the Control Panel account number. Valid Range: 0000000001 -
FFFFFFFFFE. Programming this Section as all 0 or all F will cause a Module Configuration Trouble (yellow LED = 12 flashes).
[102] Ethernet Receiver 1 DNIS
Default (000000);
The Dialled Number Information Service (DNIS) is used in addition to the Account Code to identify the Communicator module at the cen-
tral station. Valid Range: 000000 - 099999. Value is entered as a 0 followed by the 5 digit DNIS. Format is Binary Coded Decimal.
NOTE: Each Ethernet receiver must be programmed with a unique DNIS.
[103] Ethernet Receiver 1 Address
Default (127.000.000.001);
The default address enables the Communicator to operate in Unattended Mode.
Unattended Mode is used when a receiver is not available and the unit is required to perform DLS sessions.Typically used where the cus-
tomer programs the Control Panel daily due to access control and still wants to receive alarms without buying extra hardware (receiver) or
software. Programming this Section as (127.000.000.002) enables Notification Mode. Enter the Ethernet receiver 1 IP address. Format is
4 fields, each field is 3 digit decimal, Valid Range: 000 -255. This information will be provided by your central station.
NOTE: When a valid IP address has been programmed, Receiver 1 will communicate events over the Ethernet channel.
[104] Ethernet Receiver 1 Remote Port
Default (0BF5/3061);
This Section determines the remote port of Ethernet receiver 1. Valid Range: 0000 - FFFF.
[105] Ethernet Receiver 1 Local Port
Default (0BF4/3060);
Use this Section to set the value of the local outgoing port. Set the value of this port when your installation is located behind a firewall and
must be assigned a particular port number as determined by your central station system administrator. Valid Range: 0000 - FFFF.
[106] Ethernet Receiver 1 Domain Name
Default ();
Enter the Domain Name as 32 ASCII characters.
Programming this Section is not permitted on a UL/ULC listed system.

Ethernet Receiver 2 Options

[111] Ethernet Receiver 2 Account Code
Default (0000000000);
The account code is used by the central station to distinguish between transmitters. This account code is used when transmitting heart-
beat signals to the central station receiver. Signals received from the Control Panel will use the Control Panel account number. Valid
Range: 0000000001 - FFFFFFFFFE. Programming this Section as all 0 or F will cause a Module Configuration Trouble (yellow LED = 12
flashes).
[112] Ethernet Receiver 2 DNIS
Default (000000);
The Dialled Number Information Service (DNIS) is used in addition to the account code to identify the Communicator module at the central
station. Valid Range: 000000 - 099999. Value is entered as a 0 followed by 5 digit DNIS. Format is binary coded decimal.
NOTE: Each receiver must be programmed with a unique DNIS.
[113] Ethernet Receiver 2 Address
Default (000.000.000.000);
Programming the Ethernet receiver 2 IP address as 000.000.000.000 will disable Ethernet.
Enter the Ethernet receiver 2 IP address. This address will be provided by your central station administrator. Format is four fields, each
field is three digit decimal Valid Range: 0 -255.
NOTE: When a valid IP address has been programmed, Receiver 2 will communicate events over the Ethernet channel.
[114] Ethernet Receiver 2 Remote Port
Default (0BF5/3061);
This Section determines the port number used by Ethernet receiver 2. Set the value of this port when your installation is located behind a
firewall, and must be assigned a particular port number as determined by your central station administrator. Valid Range: 0000 - FFFF.
NOTE: Do not program Ethernet Receiver 1 and Ethernet Receiver 2 Local Port with the same value.
[115] Ethernet Receiver 2 Local Port
Default (0BF9/3065);
Use this Section to set the value of the local outgoing port. Set the value of this port when your installation is located behind a firewall and
must be assigned a particular port number as determined by your network administrator. Valid Range: 0000 - FFFF.
NOTE: Do not program Ethernet Receiver 1 and Ethernet Receiver 2 Local Port with the same value.
[116] Ethernet Receiver 2 Domain Name
Default ();
Programming this Section is not permitted on a UL/ULC listed system.
Enter the Domain Name as 32 Character ASCII text.

Ethernet Options

[124] Ethernet Test Transmission Time
Default (9999);
Enter a 4 digit number (0000-2359) using the 24-hour clock format (HHMM) to set the test transmission time of day. Valid Range: 00 -
23 hours (HH) and 00 - 59 minutes (MM). Programming a value of (9999) will disable the test transmission time.
NOTE: The internal date and time will automatically be programmed when it communicates with the primary receiver.
10