Programming Worksheets; System Options; Programming Options; System Test Options - DSC TL260 Manual De Instrucciones

Comunicador de alarma vía ethernet/internet
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

System Options

[001] Ethernet IP Address
Default (000.000.000.000);
|____|____|____| |____|____|____| |____|____|____| |____|____|____|
[002] Ethernet IP Subnet Mask
Default (255.255.255.000);
|____|____|____| |____|____|____| |____|____|____| |____|____|____|
[003] Ethernet Gateway IP Address
Default (000.000.000.000);
|____|____|____| |____|____|____| |____|____|____| |____|____|____|
[004] Receiver Supervision Interval
Default [0087/135]; Valid Range: 0000 - FFFF.
|____|____|____|____|
[005] System Toggle Options
[1] Ethernet Receiver 1 Supervised
|____|
[3] Supervision Type
|____|
[6] Remote firmware update
|____|
[7] Alternate Test Transmission
|____|
[006] System Toggle Options 2
[1] Ethernet Receiver 1 Enabled
|____|
[2] Ethernet Receiver 2 Enabled
|____|
[007] DNS Server IP 1
Programming not permitted on UL/ULC listed system.
Default (000.000.000.000);
|____|____|____| |____|____|____| |____|____|____| |____|____|____|
[008] DNS Server IP 2
Programming not permitted on UL/ULC listed system.
Default (000.000.000.000);
|____|____|____| |____|____|____| |____|____|____| |____|____|____|

Programming Options

[011] Installer Code
Default (CAFE); Valid Range: 0000 - FFFF.
|____|____|____|____|
[012] DLS Incoming Port
Default (0BF6/3062); Valid Range: 0000 - FFFF.
|____|____|____|____|
[013] DLS Outgoing Port
Default (0BFA/3066); Valid Range: 0000 - FFFF.
|____|____|____|____|
[021] Account Code
Default (FFFFFF); Valid Range: 000001 - FFFFFE.
|____|____|____|____|____|____|
[022] Communications Format
Default (04);Program 03 for Contact ID, or 04 for SIA.
|____|____|
[023] Panel Absent Trouble
Default (FF);Program 00 disable or FF enable.
|____|____|
[024] Panel Absent Trouble Restore
Default (FF); Program 00 disable or FF enable.
|____|____|

System Test Options

[026] Ethernet 1 Transmission
Default (FF); Program 00 disable or FF enable.
|____|____|
[027] Ethernet 2 Transmission
Default (00); Program 00 disable or FF enable.
|____|____|
[030] FTC Restore
Default (FF); Program 00 disable or FF enable.
|____|____|

Ethernet Receiver 1 Options

[101] Ethernet Receiver 1 Account Code
Default (0000000000); Valid Range: 0000000001 - FFFFFFFFFE.
|____|____|____|____|____|____|____|____|____|____|

PROGRAMMING WORKSHEETS

Default (OFF).
Default (OFF).
Default (ON).
Default (OFF).
Default (ON).
Default (ON).
[102] Ethernet Receiver 1 DNIS
Default (000000); Valid Range: 000000 - FFFFFF.
|____|____|____|____|____|____|
[103] Ethernet Receiver 1 Address
Default (127.000.000.001);
|____|____|____| |____|____|____| |____|____|____| |____|____|____|
[104] Ethernet Receiver 1 Remote Port
Default (0BF5/3061); Valid Range: 0000 - FFFF.
|____|____|____|____|
[105] Ethernet Receiver 1 Local Port
Default (0BF4/3060); Valid Range: 0000 - FFFF.
|____|____|____|____|
[106] Ethernet Receiver 1 Domain Name
Default (); 32 ASCII characters.
Programming not permitted on UL/ULC listed system.
________________________________

Ethernet Receiver 2 Options

[111] Ethernet Receiver 2 Account Code
Default (0000000000); Valid Range: 0000000001 - FFFFFFFFFE.
|____|____|____|____|____|____|____|____|____|____|
[112] Ethernet Receiver 2 DNIS
Default (000000); Valid Range: 000000 - 0FFFFF.
|____|____|____|____|____|____|
[113] Ethernet Receiver 2 Address
Default (000.000.000.000);
|____|____|____| |____|____|____| |____|____|____| |____|____|____|
[114] Ethernet Receiver 2 Remote Port
Default (0BF5/3061); Valid Range: 0000 - FFFF.
|____|____|____|____|
[115] Ethernet Receiver 2 Local Port
Default (0BF9/3065); Valid Range: 0000 -FFFF.
|____|____|____|____|
[116] Ethernet Receiver 2 Domain Name
Programming not permitted on UL/ULC listed system.
________________________________

Ethernet Options

[124] Ethernet Test Transmission Time
Default (9999); Valid Range: 00 - 23 (HH) and 00 - 59 (MM).
|____|____|____|____|
[125] Ethernet Test Transmission Cycle Default (000000);
Valid Range: 000000 - 999999 minutes.
|____|____|____|____|____|____|

Communication Path Diagnostic

[901] Diagnostic Test Transmission
[1] Ethernet 1
|____|
[2] Ethernet 2
|____|

System Information (Read Only)

[988] DNS 1 IP Address
|____|____|____| |____|____|____| |____|____|____| |____|____|____|
[989] DNS 2 IP Address
|____|____|____| |____|____|____| |____|____|____| |____|____|____|
[991] Firmware Version
|____|____|____|____|____|____|____|____|
[992] Ethernet IP Address
|____|____|____| |____|____|____| |____|____|____| |____|____|____|
[993] Ethernet Gateway Address
|____|____|____| |____|____|____| |____|____|____| |____|____|____|
[998] MAC Address
|____|____|____|____|____|____| |____|____|____|____|____|____|

System Reset Defaults

[999] Software Default
Default (99); Valid entries are 00; 55.
|____|____|
12
Default ();;
Default [OFF];
Default (OFF).
Default (OFF).

Hide quick links:

Publicidad

Tabla de contenido

Solución de problemas

loading

Este manual también es adecuado para:

Tl265

Tabla de contenido