Peg-Perego fumagalli ypsi Instrucciones De Uso página 25

of the frame (fig_b).
5 To complete the basket attachment procedure for the
front part, you are required to insert the supplied tie
(fig_1) as follows:
position it between the basket and buttons, as shown
(fig_2) and use your finger to push downwards, so as
to complete the attachment procedure (fig_3).
Repeat the same procedure for the other side of the
basket.
6 Slip the back section of the pouch under the bar
(fig_d).
Fasten the three buttons at the base of the chassis
(Fig_e).
Fasten the Velcro strap in the inside of the basket,
positioning the fabric as shown in the picture (Fig_f).
7 Close the pouch zip (fig_g).
Finally, to complete basket attachment, fasten the
basket buttons on both sides onto the chassis (fig_h).
WARNING! If you do not hook the basket on correctly,
as shown, the basket will be unable to support the
weight of loads placed in it.
8 The section of the front basket can be lowered (fig_a)
or raised (fig_b).
9 FIXED OR SWIVELLING FRONT WHEELS: to lock the
front wheels, rotate the lever anticlockwise onto the
locked padlock (fig_a), to release the wheels - turn
the lever clockwise to the unlocked padlock (fig_b).
On difficult terrain, we recommend using fixed
wheels.
10 BRAKE: press the lever down to apply the brake and
lock the frame. Do the opposite to release the brake.
11 ADJUSTABLE HANDLE BAR: to adjust the height of
the handlebar, pull the levers towards you (fig_a) and
move the handle bar until it clicks (fig_b). The handle
bar can be adjusted in several positions.
12 FOLDING: lock the front wheels into fixed position
(fig_a), put the handle bar to its lowest position
(fig b). Rotate the safety lever to the left (fig_c) and
pull the frame's internal handle towards you (fig_d).
Lift the handle until the frame is completely folded
(fig_e).
13 To fold correctly, make sure the side hook is engaged
(fig_a). When folded, the chassis will stand upright
(fig_b).
TRANSPORT: the stroller can be conveniently carried
(with the front wheels in fixed position) using the
central handle bar (fig_c).
14 All the wheels can be removed to reduce dimensions
further. To remove the back wheels: pull the lever
downwards and remove the wheel as illustrated
(fig_a). To remove the front wheels: press the tab as
shown and remove the wheels (fig_b).
SERIAL NUMBERS
15 Ypsi Chassis, has the information on the product's
production date on the lower part of the frame.
_ Product name, production date and serial number of
the chassis. This information is essential in the event
of a claim.
INSTRUCTIONS
YPSI SEAT
1 OPENING: Before opening the Ypsi Seat, remove
(without using blades) any die-cut cardboard.
Open the seat from the ends, pulling until it clicks.
2 ATTACHING THE SEAT ONTO THE CHASSIS: To fasten
the Ypsi Seat, position it on the chassis (fig_a) and
press down with both hands until it clicks (fig_b).
Ensure the Ypsi Seat is properly attached.
3 The Ypsi Seat can be attached onto the chassis in
"world-facing" (fig_a) or "mum-facing" position
(fig_b).
Always engage the brake on the chassis before
fastening and unfastening the seat.
4 REMOVING THE YPSI SEAT FROM THE CHASSIS: To
unfasten the Ypsi Seat, press the levers near the
chassis attachments (fig_a) and lift the seat at the
same time (fig_b).
5 ASSEMBLING THE PADS: attach the side pads' Velcro
straps to the seat's pad.
Turn over the reducers from the front.
Reducers attached correctly.
6 Open the buckles by pressing on the extremities and
detach (Fig. a). Open the abduction belt as shown to
make it easier to position the reducer (Fig.b).
7 Position the reducer into the seat leaving the
abduction belt on top of it (Fig.a).
Slip the Velcro strap through the seat eyelet (Fig.b)
and complete the attachment process by making the
Velcro stick under the seat. Close both buckles (Fig.c).
8 Attach both black pads, including the abduction belt
between them (Fig.a), attach both Velcro straps under
the seat pad (Fig.b) and fasten the press-stud button
(Fig.c).
9 Complete by fastening the buttons of the seat's side
pads (Fig.a) on both sides. Pads installed correctly.
10 FRONT BAR: Attach the front bar in the slots as shown
(fig.a) until you hear a click.
The front bar can be removed by pressing the two
buttons at its extremities (fig_b), or opened on one
side by pressing only one of the two buttons (fig_c).
11 HOOD: To use the hood, pull it out completely until it
clicks into place.
12 The hood comes with a mesh insert so that the
child can be seen from any position. The hood can
be further expanded by unzipping it and pulling it
forward.
13 Slide the hood's attachments on the uprights (fig_a)
to change the distance between the hood and the
seat (fig_b).
14 BED POSITION: the seat can be adjusted in three
positions that range from "sitting" to "lying", with an
intermediate position (fig_a).
Before adjusting the seat to a flatter position, the
handlebar must be extended (Fig_b). You can switch
from one position to another by pulling the lever
shown in the picture (fig_c).
15 ADJUSTING THE DEPTH OF THE SEAT: by opening the
sack's side zip, the seat depth can be increased.
When increasing the depth, the seat's pad and the
side pads must be replaced with the larger ones
(accessory provided, figure 33).
16 ADJUSTING THE HEADREST: it can be adjusted in 3
positions. To adjust:
open the zip on the seat's backrest (Fig.a),
release both Velcro straps to remove it from the
backrest (Fig.b),
remove the headrest from the front (Fig. c),
reposition it by inserting the Velcro straps at the
desired height (Fig. d) and fixing them onto the
backrest. Close the zip.
17 USING AND ADJUSTING THE CONTAINMENT BELTS:
fasten the buckles until you hear a click. Adjust
their adherence to the child by pulling the strap
towards you (arrow 1). To open the buckles, press the
extremities as shown (arrow 2) and unfasten.
18 ADJUSTING THE CHEST BELT: it can be adjusted in 2
positions.
To adjust:
open the zip on the seat's backrest and unfasten the
two Velcro straps to remove them from the backrest
(Fig.a),
remove the pad from the front (Fig. b),
reposition it by inserting the Velcro straps at the
desired height (Fig. c) and fixing them onto the
backrest. Close the zip.
The pad will adhere more or less closely to the child
- 25 -