Using The Pre-Programmed Settings - Oster PRO 1200 Serie Manual Del Usuario

6 Cup glass Jar Assembly
Threaded Jar
Locking
Bottom with
Blade
Sealing Ring
locking lever
1. Place Blade into Threaded Jar Bottom (Fig.1).
2. Place sealing ring over blade assembly. Carefully press
and tuck sealing ring into locking groove (Fig2).
3. Ensure the locking sealing ring is fully and evenly
tucked in place and holding the blade assembly to the
threaded jar bottom. For correct assembly see (Fig3).
4. I nstall the Integrated Blade Assembly onto the Jar. Turn clockwise to tighten.
B e sure the Integrated Blade Assembly is tightened to the jar before using.
NOTE: For proper installation onto Blender Motor base, make sure locking
lever rotates past the anti-rotation tabs on the Blender jar or smoothie cup.
See (Fig4). CAUTION: If Locking Lever is damaged or missing, do not
operate blender, and contact Customer Service for a replacement.
5. Put the ingredients into the jar.
6. Secure the lid and filler cap.
7. Place the jar onto the base.
8. P lug the power cord into a standard household
120/127-volt, 60 hz. AC outlet. You are now ready to start.
ALWAYS PLACE HAND ON CONTAINER COVER
WHILE OPERATING BLENDER.
8 Cup Tritan Jar Assembly
TM
1. Install the sealing ring over the blade.
2. T urn the jar upside down and place it on
a flat and stable surface.
3. Turn the blade with sealing ring upside down and place into the bottom of the jar.
4. I nstall the threaded jar bottom over the blade assembly. Turn clockwise to
tighten. Be sure the threaded jar bottom is tightened to the jar before using.
5. C hoose a recipe from the recipe book provided.
6. Put the ingredients into the jar.
7. Secure the lid and filler cap.
8. Slide the jar onto the base.
BLSTMB_16ESM1.indd 8-9
Fig1
Fig2
Incorrect Correct!
Fig3
Locking Lever
Fig4
Note: The filler cap can be used as a tool to
tighten or remove the threaded jar bottom.
Filler Cap
Threaded
Jar Bottom
8
9. P lug the power cord into a standard household 120/127-volt, 60 hz. AC outlet.
You are now ready to start.

Using the Pre-Programmed Settings

1. P ress the ON/OFF power button to turn the product on. The power light
will blink, indicating the product is active and ready to use. The light will
stay on when the motor is running.
2. S elect and Press the desired Pre-Programmed Setting Button:
- "Green/Frozen Smoothie"
- "Food Chop/Salsa"
- "Milkshakes"
3. To change your selection, press Stop followed by another Pre-Programmed
Setting button ("Frozen Drinks & Shakes" or "Food Chop")
4. Once the program is finished the product automatically stops. Please note:
You may press the "Stop" button to cancel the program at any time. The
blinking bule light indicates that the blender is ready.
5. Press the ON/OFF power button to turn the product off. This product is
pre-programmed to turn off automatically if not used for a period of several
minutes. All lights will turn off when the unit automatically powers down.
Using the Manual Controls
The Manual Controls include:
Low
Med
High
Pulse
Stop
Use these controls for personal recipes or to continue blending after a
Programmed Setting is finished.
1. P ress the ON/OFF power button to turn the product on. The power light
will blink, meaning the product is active and ready to use. The light will stay
on when the motor is running.
2. Put the ingredients into the jar.
3. Secure the lid and the filler cap.
Using High
1. Press the "High" button to run the product at a high speed.
2. Press the "Stop" button to cancel the operation at any time.
3. Press the ON/OFF power button to turn the product off.
Using the Medium
1. Press the "Medium" button to run the product at a medium speed.
2. Press the "Stop" button to cancel the program at any time.
3. Press the ON/OFF power button to turn the product off.
Using the Low
1. Press the "Low" button to run the product at a low speed.
2. Press the "Stop" button to cancel the program at any time.
3. Press the ON/OFF power button to turn the product off.
9
5/18/16 11:40 AM