stayer HILO Serie Manual De Instrucciones página 32

gb
ARC DOES NOT APPEAR
a ) Check unit, torch and earth clamp connections
UNIT IS NOT ON WHEN THE TORCH SWITCH IS
CONNECTED
a ) Thermostat intervention
b ) Check torch switch operation
UNIT DOES NOT WORK – LUMINOUS SWITCH IS NOT
ON
a ) Verify the electric grid connection
b ) Verify the differential switch or the electric grid fuse
5_SERVICE AND MAINTENANCE
INSTRUCTIONS
Specific torches instructions:
- Clean the torch nozzle adhered projections to avoid cut
circuits and gas turbulences. Use a steel brush.
- Avoid projections adherences, using a specific silicone-free
spray
- Periodically check the pinch rollers and breaking reel
- Verify the wire properly goes through
- Control the calibrated contact tip and replace it when
necessary in order to avoid wire contact loss with the nozzle
Do not use the torch as a hammer to eliminate welding dirt or
to align sheets.
Reparation service
The technical service staff will advise you with all the doubts
and questions you may have about the reparation or the
maintenance of your product, just as with replacement
components. All the illustrations and lists of parts of the unit
are also available in the web from: info@grupostayer.com
Our technical advisors' team will gladly guide you about
acquisition, application and adjustment of the products and
accessories.
Guarantee
Guarantee card
Along the rest of the documents included in the unit, you
will find the guarantee card. You should completely fill the
guarantee card, attaching a copy of it with the purchase
receipt or ticket, which will be given to the seller in exchange
of an acknowledgement.
NOTE! If the card is missing, immediately ask your seller
to get it.
The guarantee covers the mechanization or manufacturing
failures. It is over whenever the components have been
disassembled, manipulated or repaired out of the factory.
Disposal
We recommend the electric tools, accessories and packaging
to be under an eco-friendly recovering process.
Only for EU countries:
Do not throw electric tools to the trash bin!
According to the European Directive 2012/19/
UE on electric and electronic devices, after its
transposition into national law, electric tools must
be separately collected in order to be ecologically
recycled.
Modification rights reserved
All manuals and user guides at all-guides.com
6_REGULATORY MARKING
REGULATORY MARKINGS EXPLANATION
Pos. 1 – Name, address and the brand manufacturer, supplier
or importer.
Pos. 2 – Identification of the model
Pos. 3 – Model traceability
Pos. 4 – Welding power source symbol
Pos. 5 - Equipment complied regulations reference
Pos. 6 – Welding process symbol
Pos. 7 – Symbol of usage in electric shock increased risk
environments
Pos. 8 – Welding current symbol
Pos. 9 – Nominal no-load voltage
Pos. 10 – Voltage range and nominal output current
Pos. 11 – Power source duty cycle
Pos. 11a – 45% Duty cycle
Pos. 11b – 60% Duty cycle
Pos. 11c – 100% Duty cycle
Pos. 12 – Nominal cutting current (I2)
Pos. 12a – Current value for a 45% duty cycle
Pos. 12b – Current value for a 60% duty cycle
Pos. 12c – Current value for a 100%
Pos. 13 – Load voltage (U2)
Pos. 13a – Voltage value for a 45% duty cycle
Pos. 13b – Voltage value for a 60% duty cycle
Pos. 13c – Voltage value for a 100% duty cycle
Pos. 14 – Power supply symbol
Pos. 15 – Power supply current nominal value
Pos. 16- Maximum nominal power supply current
Pos. 17- Maximum effective power supply current
Pos. 18 – IP protection grade
- 32 -
1
2
4
6 8
11
12
7 9
13
14 15
18
3
5
10
11a 11b 11c
12a 12b 12c
13a 13b 13c
16 17