Stanley FATMAX SFMEH200 Traducido De Las Instrucciones Originales página 7

The side handle can be fitted to suit both right-handed and
left-handled users.
Turn the grip counter-clockwise until you can slide the side
u
handle onto the front of the tool.
Rotate the side handle into the desired position.
u
Tighten the side handle by turning the grip clockwise.
u
WARNING! When using the tool, remember to install the side
handles properly.
Fitting an accessory (Fig A)
Clean and grease the shank (11) of the SDS Plus bit.
u
Insert the accessory bar into the SDS + Chuck (7).
u
Push the accessory down and turn it slightly until it fits into
u
the slots.
Pull on the accessory to check if it is properly locked.
u
The hammering and drilling function requires the acces-
sory to be able to move axially several centimetres when
locked in the tool clamp.
To remove the accessory, pull back the sleeve (6) and pull
u
out the accessory from the tool clamp.
Fitting dust collector (Fig E)
Insert the SDS Plus bit (11) into dust collector (14), then
u
insert the bit (11) with dust collector into tool clamp (7).
Use the dust collector only when the unit is used for
u
upright drilling (Fig F).
Use
WARNING! Always wear gloves when you change acces-
sories. The exposed metal parts on the tool and accessory
may become extremely hot during operation. Please operate
tool with normal load. Do not overload. Do not abuse the tool,
please refer instruction manual to use the tool correctly.
WARNING! Before drilling into walls, floors or ceilings, check
for the location of wiring and pipes.
Setting the drilling depth (Fig A)
The depth stop is a convenient feature to ensure uniformity
in drilling depth. Loosen the side handle to adjust the depth
gauge according to the required depth. After that, tighten the
side handle.
Slacken the side handle (9) by turning the grip counter-
u
clockwise.
Set the depth stop (8) to the required position. The maxi-
u
mum drilling depth is equal to the distance between the tip
of the drill bit and the front end of the depth stop.
Tighten the side handle by turning the grip clockwise.
u
Switching on and off (Fig A)
WARNING! Before plugging in to the power source, make
sure the variable speed switch can be flipped freely, and can
return to its original position once released.
(Original instructions)
Please check switch lock on position before turn on and make
sure switch lock off before plugging in to the power source.
To switch the tool on, press the variable speed switch (3).
u
The tool speed depends on how far you press the switch.
As a general rule, use low speeds for large diameter drill
u
bits and high speeds for smaller diameter drill bits.
For continuous operation, press the lock-on button (2) and
u
release the variable speed switch.
To switch the tool off, release the variable speed switch.
u
To switch the tool off when in continuous operation, press
the variable speed switch once more and release it.
Replacing the SDS-Plus tool holder with the key-
less chuck (SFMEH210 - Fig G)
Turn the locking collar (6) into the unlocking position and
u
pull the SDS Plus Tool Holder (7) off.
Push the keyless chuck (13) onto the spindle and turn the
u
locking collar (14) to the locking position.
To replace the keyless chuck with the SDS Plus tool holder,
first remove the keyless chuck the same way the tool holder
was removed. Then place the tool holder the same way the
keyless chuck was placed making sure to turn the locking
collar to the locking position.
WARNING! Never use standard chucks in the hammer-drilling
mode.
Selecting the operating mode (Fig B)
The tool can be used in the following operating modes:
Rotary drilling: for drilling into steel, wood and
plastics.
Hammer drilling: for concrete and masonry
drilling operations. Bit rotation: non-working
position used only to rotate a flat chisel into the
desired position.
Hammering only: for light chipping and
chiselling. In this mode the tool can also be
used as a lever to free a jammed drill bit.
1. To select the operating mode, press the mode selector
button and rotate the mode selector switch (5) until it
points to the symbol of the required mode.
2. Release the mode selector button and check that the
mode selector switch is locked in place.
WARNING! Do not select the operating mode when the tool
is running.
Proper hand position (Fig D, Fig F)
WARNING! To reduce the risk of serious personal injury,
ALWAYS use proper hand position as shown.
WARNING! To reduce the risk of serious personal injury,
ALWAYS hold securely in anticipation of a sudden reaction.
ENGLISH
7