Stanley FATMAX SFMEH200 Traducido De Las Instrucciones Originales página 8

ENGLISH
Proper hand position requires one hand on the side handle
(9), with the other hand on the main handle (1).
Rotary drilling (Fig B, Fig D, Fig C1/C2,
Fig G )
For drilling in steel, wood and plastics, set the operating
u
mode selector (5) to the
Fit the drill chuck assembly. Depending on your tool, follow
u
either of the following instructions:
SFMEH210: Replace the SDS Plus tool holder (7) with the
keyless chuck (13).
WARNING! Never use drill chucks in the hammer drilling
mode.
Hammer drilling (Fig B)
For hammer drilling in masonry and concrete, set the
u
operating mode selector (5) to the
The drill bit has to be placed accurately onto the drill hole
u
position. After that, pull the switch for optimal effects.
Make sure the tool is in the correct position to prevent the
drill from deviating from the hole.
When the drill hole is clogged with debris or fine powder,
u
please don't exert any more pressure. Tool should be put
in free-running state before removing part of the drill bit
from the hole. If repeated a few times, the blockage in the
hole would be cleared, and normal drilling can resume.
WARNING! When the drill bit hits the steel rebar in the ce-
ment, the tool may recoil dangerously. Please hold the tool
tightly in a balanced and stable position at all times to prevent
it from recoiling dangerously.
Safety clutch
All rotary hammer are equipped with a safety clutch that re-
duces the maximum torque reaction transmitted to the opera-
tor in case of jamming of a drill bit. This feature also prevents
the gearing and electric motor from stalling. The torque limiting
clutch has been factory-set and cannot be adjusted.
Overload coupling device
If the drill bit is caught or hooked, the driving force transmitted
to the drill shaft will be cut off. This would generate a strong
recoil, so it would be necessary to hold the tool tightly with
both hands to remain in a stable position.
Chipping and chiselling (Fig B)
Set the mode selector switch (5) to the"hammering only"
u
position.
Insert the appropriate chisel and rotate it by hand to lock it
u
into position.
Adjust the side handle (9) as required.
u
Switch on the tool and start working.
u
Always switch off the tool when work is finished and
u
before unplugging.
8
(Original instructions)
position.
position.
WARNING! Do not use this tool to mix or pump easily com-
bustible or explosive fluids (benzine, alcohol, etc.). Do not mix
or stir inflammable liquids labelled accordingly.
Accessories
The performance of your tool depends on the accessory used.
STANLEY FATMAX and Piranha accessories are engineered
to high quality standards and designed to enhance the perfor-
mance of your tool. By using these accessories you will get
the very best from your tool.
Maintenance
Your STANLEY FATMAX corded/cordless appliance/tool has
been designed to operate over a long period of time with a
minimum of maintenance. Continuous satisfactory operation
depends upon proper tool care and regular cleaning.
WARNING! Before performing any maintenance on corded/
cordless power tools:
Switch off and unplug the appliance/tool.
u
Or switch off and remove the battery from the appliance/
u
tool if the appliance/tool has a separate battery pack.
Or run the battery down completely if it is integral and then
u
switch off.
Unplug the charger before cleaning it. Your charger does
u
not require any maintenance apart from regular cleaning.
Regularly clean the ventilation slots in your appliance/tool/
u
charger using a soft brush or dry cloth.
Regularly clean the motor housing using a damp cloth. Do
u
not use any abrasive or solvent-based cleaner.
Regularly open the chuck and tap it to remove any dust
u
from the interior (when fitted).
Mains plug replacement (U.K. & Ireland only)
If a new mains plug needs to be fitted:
Safely dispose of the old plug.
u
Connect the brown lead to the live terminal in the new
u
plug.
Connect the blue lead to the neutral terminal.
u
WARNING! No connection is to be made to the earth terminal.
Follow the fitting instructions supplied with good quality plugs.
Recommended fuse: 10 A.
Protecting the environment
Z
Separate collection. Products and batteries
marked with this symbol must not be disposed of
with normal household waste.
Products and batteries contain materials that can be recov-
ered or recycled reducing the demand for raw materials.
Please recycle electrical products and batteries according to
local provisions. Further information is available at
www.2helpU.com