SOLAC CA4810 Instrucciones De Uso página 9

FILLING THE BEAN CONTAINER
- When (B) Icon is flashing, the appliance needs to be filled with coffee
bean:
- Remove the bean container lid (12)
- Slowly pour in the coffee beans.
- Install back the container lid (12)
IMPORTANT: Fill the coffee bean container (11) with coffee beans
only. Grounded coffee, instant coffee, caramelized coffee and any
other objects may damage the machine.
PREPARING FROTHY MILK FOR COFFEE
- Since the temperature of steam is higher than the temperature of
espresso, so coffee should be prepared before making frothy milk;
otherwise the espresso might be burnt.
- Prepare the coffee with large cup.
- Turn the steam nozzle toward (6) to the Drip tray (1).
- Press the steam button (H). Steam indicator light (8) will flash. Then
the appliance is heating up and draining the residual water into the Drip
Tray or another container.
- After the steam indicator light (8) stop flashing and stay on, place a
container with milk under the steam nozzle and immerse the steam
nozzle about 5 cm deep into the container.
- Press the steam button (H) again.
- Swivel the container while the hot steam comes out.
- When the milk is hot enough with froth appeared. Then press again the
steam button to stop the steam.
- Use a wet towel to clean the nozzle cover and metal tube. (Refer to
"DAILY CLEANING OF THE APPLIANCE").
- Pour the hot frothy milk into the coffee.
- Now you can enjoy your coffee.
HOT WATER
- The appliance can dispense hot water by simply pressing the hot water
button (I). The hot water button (I) and the illumination (8) will lights up
indicates that the appliance is heating up the water. When the hot water
button and the illumination turn off, the water is ready to serve.
FAVOURITE FUNCTION
- You can use the Favorite function to memorize an additional volume
selection for soft coffee, strong coffee or American coffee (Additional to
only one of the three).
SET UP THE FAVORITE COFFEE SETTING
a) Press and hold the Favorite button (L) for 2 second, then the mild
coffee (K), strong coffee (J), and hot water button (I) will flash and you
can select any one to memorize the volume.
b) When you select either strong espresso, mild espresso or hot water.
You will see the drinks come out, and then you can press and immedia-
tely hold to keep dispensing the drinks and stop it by release the button.
After that the volume will be memorized.
USING THE FAVORITE FUNCTION
- Once the Favorite function is programmed, just press the Favorite
Function button (L), and the memorized drink will come out.
DAILY CLEANING OF THE APPLIANCE
- Timely cleaning and maintenance of the appliance is very important in
prolonging the life of the appliance.
CLEANING BREWING UNIT (17)
- Remove the external drip tray (1).
- Empty the water inside the drip tray in the sink and wash it with fresh
water. Dry it afterwards.
- Slides open the internal drip tray (3) and the coffee grounds container
(4).
- Empty the coffee grounds container and wash it with fresh water. Dry it
afterwards.
Note: When the icon (C) lights up, the coffee grounds container
needs to be empty.
- Pull down the service door (Fig 2).
- Remove the service door (16) (Fig 3).
- Press the release (Orange) knobs of Brewing group (17) (Fig 4).
- Remove the brewer (17) (Fig 5).
- Wash the brewer with fresh water. Dry the brewer afterwards.
- Insert back the brewer (17) to its original position and install back the
service door (16) its original position.
Note: When Icon (D) lights up stably, it indicates that the brewer (17)
is missing / installed improperly. When Icon (D) is flashing, it indica-
tes that the service door (16) is missing/ installed improperly.
- Place the coffee grounds container (4) on the internal drip tray (3) and
insert back into it original position.
Note: When Icon (C) is flashing, the coffee grounds container (4) is
missing.
- Place the external drip tray (1) at it original position.
CLEANING STEAM NOZZLE (5-6-7)
- Unlock the nozzle cover (6) by turning it to left (Sometimes you may
need a pliers type tool). Then pull it downward to remove (Fig 6).
- Pull the metal tube (5) downward to dis-assemble the nozzle cover and
metal tube (Fig 7).
- Wash the nozzle cover (6) with warm running water and use needle or
bristle of brush to clean the hole (Fig 8).
- Wash the metal tube (5) with warm running water and use needle or
bristle of brush to clean the hole (Fig 9).
- Replace the metal tube (5) back to the nozzle cover (6). Then push
upward to place the nozzle cover (7) back. And turn it to right to lock it
(Fig 10).
TURNING OFF THE MACHINE
- Switch off the appliance by pressing the power on/off button (G).
AUTO-SHUT OFF
- The Appliance is equipped with auto-shut off. Depending on the mode
you have selected the appliance will have different auto-shut off timing
(See MODE SELECTION).
FURTHER SETTING
ADJUSTIING THE VOLUME OF YOUR COFFEE/HOT WATER
- You can memorize your desired volume of coffee for both strong coffee
and mild coffee and also the hot water from 25ml to 250ml.
- When making your coffee (either strong coffee (J) or mild coffee (K)
or dispensing hot water (I), press and immediately hold the button you
selected. The appliance will continue to make the cup of coffee.
- When the volume of coffee meets your desired volume, release the but-
ton. Two beep sounds will be heard indicates that the volume of coffee
is being memorized.
GRINDING ADJUSTMENT (FIG 11)
- You can adjust the grinder to suit the roast of your coffee by turning
adjuster knob in the bean container (Fig 11):
- To adjust the grind size, you can turn the adjustment knob, ALWAYS
while the grinder is grinding the coffee.
CAUTION: Never do the grinding adjustment when the grinder is not
operating. It may damage the grinder.
- The dots on the adjuster knob indicate the fineness of the grind.
MODE SELECTION
- The machine has two different setting: default setting, ECO mode and