Cleaning & Maintenance - SOLAC CA4810 Instrucciones De Uso

speed mode. In ECO mode, the appliance helps to save more energy.
In speed mode, the user can make their coffee faster than in default
setting.
- Below you will see a chart with the active functions of each Mode.
ECO Mode
Illumination
No
Light
Pre-brewing* Yes
Auto shut off
10mins
time
Cup Volume
Yes
memory
*Note: The pre-brewing function moistens the grounded beans in
the brewer with a small amount of water before full extraction. This
expands the coffee grounds to build up a greater pressure in the
brewer which help extraction of all the oils and full flavor from the
grounded beans.
TO SELECT THE DESIRED MODE:
- When the machine is in standby condition, press and holds the ON/
OFF Button (G) for 5 seconds, so it (G) will begin to flash. Then release
and pass to the next point
- The Icon ON/OFF (G) will then be flashing and the following button will
have the following indications
- To know which mode it is in, the table below indicates what is shown in
the different settings:
Hot water
button (I)
In ECO Mode Lights ON
In Speed Flashing
Mode
In Default Flashing
Setting
- To change the MODE, press the hot water button (I) for ECO mode,
strong espresso button (J) for speed mode and mild espresso button
(L) for default setting.Two Beep sound will be heard indicates that the
mode is being selected. (Note: If you are pressing the relative lights on
button for each mode, the machine will not response).
- If you would like to remain the setting unchanged, press ON/OFF
button (G again or wait for 5 seconds for the machine to return to the
standby condition.
CLEANING & MAINTENANCE
SELF-CLEANING
- When icon (E) is flashing, it indicates that the appliance needs to
undergo self-cleaning. The appliance will remain in the best condition
if this function is performed at least once a month or more regularly
depending on the hardness of water used. It is also suggested:
- Fully fill the water tank (14).
- Adding one pack of cleaning agent included in the box to the water
tank.
IMPORTANT: Do not use vinegar or other cleaning agent to do self-
cleaning of this appliance. The cleaning agent might damage the
appliance.
- Plug in the appliance.
- Place a sufficient large container under the coffee spout.
- In standby condition, press and hold ON/OFF Button (G) and strong
coffee button (J) at same time, for 5 seconds. A beep sound will be
heard with Icon (E) and strong coffee button (J) will be flashing.
- Press strong coffee button (J) to confirm undergoing the self-cleaning
process. To resume back to the standby condition, press ON/OFF
button (G).
- Icon (E) will be flashing indicates that the appliance is undergoing the
Speed Mode Default Setting
Yes Yes
No Yes
30mins 20mins
Yes Yes
Strong coffee Mild coffee
button (J) button (K)
Flashing Flashing
Lights ON Flashing
Flashing Lights On
self-cleaning process. (Caution: Keep skin/body away from the hot
water.)
- When all the water in the water tank is being dispensed out, Icon (A)
(Low water level) and strong coffee button (J) will be flashing. Remove
all the remaining solution in the water tank (14) and fill the tank with
normal tap water until the MAX position. When water is filled into the
water tank, Icon (A) will goes off. Then the appliance will continue the
descaling process, the appliance will brew half of water tank first and
then waiting for around 1min, after that will brew the outstanding water
from the water tank.
- When the self-cleaning process is completed, the appliance will switch
off automatically.
Note: To ensure the descaling process can be completed, please be
patient during the process and make sure the applicant switch off
automatically.
EMPTY SYSTEM FUNCTION
- The empty system function is recommended to be used before long
period of non-use, frost protection and before talking to repair agent.
- In standby condition, press and hold the ON/OFF button (G) and mild
coffee button (K) together for 5 seconds.
- Empty System Icon (F) will then be flashing.
- Remove the water tank from the appliance. Icon (F) will light up stably
indicates that the empty system is under process. You can press ON/
OFF Button (G) before removing the water tank (14) to resume back to
the standby condition.
- When the empty system function is completed, the appliance will switch
off automatically.
Important: After perform EMPTY SYSYEM FUNCTION; when you use
the coffee machine again, press the hot water button (I) until water
can come out from spout (5) when the coffee maker is reused again.
MANUAL RINSING
- You can perform a manual rinsing cycle to clean the coffee nozzle after
use. It is also suggested to perform a manual rinsing if the appliance
has not been used for a long period of time.
- In standby condition, press and hold the ON/OFF Button (G) and hot
water button (I) together.
- The hot water button(I), strong coffee button (J) and mild coffee button
(K)will then goes off. The coffee nozzle (9) will then dispense a small
amount of water which is used for the rinsing.
Danger: Water comes out of the coffee nozzle is hot and is collected
in the drip tray underneath. Avoid contact with splashes of water.
- After rinsing, the appliance will return to the standby condition.
CLEANING THE APPLIANCE
- Disconnect the power cord (15) from the main power outlet.
- Empty all the water in the internal (3) and external drip tray (1)
- Use a damped cloth or non-scratching cleaner to clean the water stains
on the appliance.
IMPORTANT: Never use any abrasive, vinegar or descaling agents
not included in the box to clean the appliance.
CLEANING COFFEE POWDER OUTLET
- Coffee grounds may stick on the wall of ground outlet of appliance,
on the way to Brewing unit (17), after an extended period of use. It is
suggested to clean the outlet by following steps to ensure that coffee
grounds can make it to the brewer.
- Push the service door recess area (Fig 2)
- Take out the service door (Fig 3)
- Press the release knob of brewer (Fig 4)
- Take the brewing unit out (Fig 5)
- Use Cleanness Brush (18) to clean the powder outlet (Fig 12)
TROUBLESHOOTING