Descargar Imprimir esta página

JVC DT-V1710CG Instrucciones página 41

Monitor multiformato
Ocultar thumbs Ver también para DT-V1710CG:

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

CONTROLS AND FEATURES
(INPUT CARD: OPTIONAL)
COMPONENT/RGB INPUT CARD (IF-C01COMG)
G / Y
IN
OUT
B/P
/B-Y
B
1
IN
OUT
R/P
/B-Y
R
4
IN
OUT
HD/C
S
2
IN
OUT
VD
IN
IN
OUT
OUT
AUDIO
3
IN
OUT
Compatible signal formats:
480/60i, 576/50i, 576/50p, 480/60p,
720/60p, 1035/60i, 1080/50i, 1080/60i,
1080/24psF
VIDEO INPUT CARD (IF-C01PNG)
VIDEO 1
1
IN
OUT
VIDEO 2
IN
OUT
2
Y/C IN
EXT .SYNC
3
IN
OUT
AUDIO 1
4
IN
OUT
AUDIO 2
5
Compatible signal formats:
NTSC (3.58 MHz), PAL (4.43 MHz),
black-and-white (50 Hz/60 Hz)
Component/RGB signal input/output terminals
1
Input (IN) and output (OUT) terminals for component (colour difference) or
RGB signals.
Select component signal: INPUT SELECT A (SLOT1)/C (SLOT2)/E (SLOT3)
Select RGB signal
: INPUT SELECT B (SLOT1)/D (SLOT2)/F (SLOT3)
* The IN and OUT terminals are bridge-connected (auto termination).
Synchronized signal input/output terminals
2
Input (IN) and output (OUT) terminals for the vertical, horizontal or complex
synchronized signals.
• To use these terminals, set "SYNC SELECT" to "EXT".
Refer to "SYNC SELECT" on page 19 for more information.
Audio input/output terminals
3
Input (IN) and output (OUT) terminals for the analogue audio signals.
• The IN and OUT terminals are bridge-connected.
Connection terminal
4
Attach to the connection terminal of your Multi-Format Monitor.
1
Composite signal input/output terminals (VIDEO 1, VIDEO 2)
Input (IN) and output (OUT) terminals for the composite video signals of the
NTSC, PAL, and black/white (50 Hz/60 Hz).
NTSC and PAL are switched in the "COLOR SYSTEM". Refer to "COLOR
SYSTEM" on page 19.
Select VIDEO 1: press INPUT SELECT A (SLOT1)/C (SLOT2)/E (SLOT3) buttons.
Select VIDEO 2: press INPUT SELECT B (SLOT1)/D (SLOT2)/F (SLOT3) buttons.
* The IN and OUT terminals are bridge-connected (auto termination).
2
S-video signal input terminal (only for VIDEO 2)
Input terminal for the S-video signal.
• When an S-video signal is input to this terminal and a video signal is input to VIDEO
2, the S-video signal has priority over the video signal.
3
Synchronized signal input/output terminals (for both VIDEO
1 and VIDEO 2)
Input (IN) and output (OUT) terminals for the complex synchronized signals.
To use these terminals, set "SYNC SELECT" to "EXT". Refer to "SYNC
SELECT" on page 19 for more information.
NOTES:
• When an external synchronized signal is input, external synchronization is prioritized
for both VIDEO 1 and VIDEO 2.
• External synchronization does not function when a video signal (except black burst
signal) is included in the complex synchronized signal.
Audio signal input/output terminals (for both VIDEO 1 and
4
VIDEO 2)
Input (IN) and output (OUT) terminals for analogue audio signals
corresponding to VIDEO 1 and VIDEO 2.
• The IN and OUT terminals are bridge-connected.
Connection terminal
5
Attach to the connection terminal of your Multi-Format Monitor.
7

Publicidad

loading

Este manual también es adecuado para:

Dt-v1910cgDt-v1710cg/uDt-v1710cg/e