Publicidad
Idiomas disponibles
Idiomas disponibles
Babyviewer KS-4245
9
Installing the Babyviewer KS-4245
9.1
Fine tuning
•
Place the camera in a convenient location, point the lens of
the camera to the observation area.
•
Adjust the angle by rotation the camera.
CAUTION
Do not place the camera and wires within the baby's reach!
Fix the camera at least 1 meter away from the baby.
10 Operation and use
10.1
Switching the baby unit and parent unit on
and off
– Press the on/off switch
unit. The display
is activated.
20
– Slide the on/off switch
unit. The on/off LED
The parent unit will try to establish a connection
with the baby unit. If captured image from the
camera is displayed, a connection has been
established.
– Press the on/off switch
unit (press and hold until the display goes blank).
– Slide the on/off switch
baby unit.
10.2
Checking the connection between the parent
unit and the baby unit
You should always check the wireless connection when you use
the babyphone for the first time.
– Put the parent unit in the same room as the baby unit,
separated by at least two metres.
– Switch on both devices. The parent unit will try to
establish a connection with the baby unit.
– The display of the parent unit will show the captured
image from the baby unit after the connection has been
established (monitor mode).
– The sounds picked up by the microphone
reproduced by the parent unit.
– The volume of the reproduced sound is indicated by the
volume LED's
at the top of the parent unit.
14
The higher the volume, the more LED's are on.
– If no connection is established, the out of range icon is
displayed and a beep is audible.
10.3
Out of range indication
The maximum range between the parent- and baby unit is 300
meter in open area. Different factors, such as bricks and plaster
walls, will reduce the range. Moreover, reinforced concrete floors
will influence the range tremendously.
In a residence, normal operating range is up to 50 meters and 2
floors.
– If the connection is interrupted, the out of range icon is
displayed and a beep is audible.
– Reduce the distance between the parent and baby units
until a new connection is established.
10.4
Setting the reproduction volume of the
parent unit
There are 5 volume levels.
– Press button
to increase the volume.
16
– Press button
to decrease the volume.
17
10.5
Setting the parent unit display brightness
When the display in on.
– Press the menu button
icon is displayed.
– Press the up
or down button
16
desired brightness (5 steps).
– Press the menu button
to switch on the parent
29
up to switch on the baby
4
is activated.
to switch off the parent
29
down to switch off the
4
are
6
once. The Brightness
23
to select the
17
to confirm.
23
– After 10 seconds the parent unit will switch back to
monitor mode.
10.6
Temperature indication
When the display is on, the baby's room temperature is displayed
in the right lower corner.
To set the temperature unit:
– Press the menu button
icon is displayed.
– Press the up
or down button
16
(Celsius), °F (Fahrenheit) or "OFF", to switch the
temperature indication off.
– Press the menu button
– After 10 seconds the parent unit will switch back to
monitor mode.
10.7
Talking with your baby
You can use the parent unit to talk with your baby.
Allow your baby to get used to the talk function
before you use it in practice.
– Press the Talk button
it pressed.
– Hold the parent unit vertical with the microphone
approximately 10 cm from your mouth, and speak into
the microphone.
– Release button
24
PTT
PTT
10.8
Playing a lullaby
There are 5 pre-programmed lullabies that you can play on the
baby unit.
– To play the currently selected lullaby or stop playback,
press the play button
– To select a different lullaby, repeatedly press the lullaby
button
until the desired lullaby is selected. The
19
lullaby icon will display the selected lullaby (1 to 5). If no
number is displayed, next to the lullaby icon, all songs
will be played successively.
When the lullaby starts playing, you have 10 seconds to set the
volume of the lullaby.
– Press the up button
the down button
17
•
10 seconds after starting or selecting the
lullaby, the parent unit will return to monitor
mode. The up button
button
the volume of the parent unit.
•
To set the volume of the lullaby in monitor
mode, switch the lullaby off and on using
the button
volume.
10.9
Switching the night light on and off
– Press the menu button
icon is displayed.
– Press the up
or down button
16
the night light "ON" (night light
– Press the menu button
– After 10 seconds the parent unit will switch back to
monitor mode.
10.10 Voice activated transmission (VOX)
During night and to save energy, the Babyviewer KS-4245 can be
set in VOX mode.
In VOX mode, the display will be activated as soon as the
microphone of the baby unit will capture sound.
You can set the sound detection sensitivity (VOX) of the
babyphone. If the sensitivity is set to high, the baby unit will pick
up weaker sounds.
– Press button
4 times. "VOX" is displayed.
23
– Repeatedly press button
VOX sensitivity.
twice. The temperature
23
to °C
17
to confirm.
23
on the parent unit and hold
24
PTT
PTT
when you have finished talking.
on the baby unit.
18
to increase the volume or
16
to decrease the volume.
and down
16
can than only be used to set
17
first before selecting the
18
3 times. The night light
23
to switch
17
is on) or "OFF".
2
to confirm.
23
or
to set the
16
17
®
5
Publicidad
