Olivetti ECR 5600 Guía De Usuario página 14

4. PERSONALIZE THE RECEIPT HEADER
1. Open the printer compartment cover and slide the control switch to the PRG position.
2. Switch the cash register to the receipt header definition mode by pressing the [#/NS] key repeatedly until
displaying the message "H01" indicating the first line of the receipt header.
3. Select the receipt header line that you wish to personalize by pressing the [Department 1/9] key repeatedly until
displaying the desired line number on the left-hand side of the operator display. Remember that a total of four
header lines can be personalized. You can scroll backward through the receipt header lines by pressing the
[Department 5/13] key repeatedly.
4. Enter the letters or characters of the string you wish to define. With reference to the section entitled "Caption
Programming Using the Alphanumeric Keypad and Character Table", use just the alphanumeric keypad to
enter capital non-accented letters or the alphanumeric keypad in combination with the Character Table to enter
small letters, accented capital and small letters, special characters or symbols. Remember that the receipt
header can be up to 24 characters long.
5. Press the [Check] key to store your entry. This new line is automatically printed.
6. Repeat steps 3, 4 and 5 if you wish to program the remaining three programmable header lines.
7. Exit from this programming sequence by pressing the [Amt Tend/TOTAL] key.
8. Program another feature or exit the program mode by sliding the control switch to the OFF position.
Example: Change the third line of the default header to / PLEASE COME AGAIN / with the appropriate
spaces before and after to center this new string using the Character Table.
Type/Press:
[#/NS] + [#/NS] + [#/NS] + [#/NS] + [Department 1/9] + [Department 1/9] + [00, sixteen times] +
[0, three times] + [1] + [5, three times] + [9, twice] + [8] + [1, four times] + [9, twice] + [0] + [0] +
[8, three times] + [6, three times] + [0] + [6] + [9, twice] + [0] + [0] + [8] + [4] + [8] + [4, three times] +
[6, twice] + [0, four times] + [00, sixteen times] + [Check] + [Amt Tend/TOTAL]
5. PROGRAM A CURRENCY EXCHANGE RATE
1. Open the printer compartment cover and slide the control switch to the PRG position.
2. Type the identification number [1 to 4] corresponding to the foreign currency exchange rate that you wish to
define.
3. Type the [decimal point position] of the exchange rate (0-8 digits after the decimal point).
4. Type the [decimal point position] of the converted amount (0-3 digits after the decimal point).
5. Type the [exchange rate] using up to six digits without specifying any decimal point.
6. Press the [Sub Total] key to store the exchange rate.
7. Program another feature or exit the program mode by sliding the control switch to the OFF position.
Example: Program the first exchange rate as 1 GBP = 1.471 EURO.
Type/Press:
[1] + [3] + [2] + [001471] + [Sub Total]
6. SET A FIXED VAT RATE
1. Open the printer compartment cover and slide the control switch to the PRG position.
2. Type the [number] that represents the VAT (1 for VAT1, 2 for VAT2, 3 for VAT3 and 4 for VAT4).
3. Press the [Card] key.
4. Type the VAT rate. Up to five digits can be used, and you MUST enter three digits after the desired decimal place.
For example, to enter a 5.5% VAT rate, type [5500]; to enter a 16% VAT rate, type [16000].
5. Press the [Amt Tend/TOTAL] key.
NOTE: If you make an error, press the [C] key and start again from step 2.
6. Program another feature or exit program mode by sliding the control switch to the OFF position.
Example: Set a VAT1 rate of 5.5%, VAT2 rate of 7%, VAT3 rate of 16% and a VAT4 rate of 20%.
Type/Press:
[1] + [Card] + [5500] + [Amt Tend/TOTAL]
[2] + [Card] + [7000] + [Amt Tend/TOTAL]
[3] + [Card] + [16000] + [Amt Tend/TOTAL]
[4] + [Card] + [20000] + [Amt Tend/TOTAL]
8