Publicidad
Idiomas disponibles
Idiomas disponibles
EN
To activate the "Timer", turn the timer knob right
round in an clockwise direction and then turn it
back in the opposite direction to the desired
length of time: an acoustic signal will warn you
when the count-down is finished.
Setting the "Analogue timer"
To set the time shown by the clock, briefly press
the knob 4 times until the
Then, to increase or decrease the time
displayed in 1-minute intervals, turn the knob
clockwise or counter-clockwise and the minute
hand will move in 1-minute intervals either
clockwise or counterclockwise.
When 10 seconds have elapsed from the last
adjustment of the electronic timer, it
automatically exits from time-setting mode.
Manual cooking
When not activated, the timer allows manual
cooking by using the thermostat and the
function knobs of the oven.
Programming the "End-of-cooking time"
Programming the "End-of-cooking time" allows
you to start immediately and finish cooking
automatically based on the programmed time.
To program the "End-of-cooking time", press
the knob briefly 2 times until the
flashes.
To increase or decrease the cooking time in
1-minute intervals, turn the knob clockwise or
counterclockwise and the minute hand moves
by 1 minute clockwise or counter-clockwise.
The
icon will flash for 10 seconds after the
last turn. The program can be confirmed by
pressing the knob so long as at least 2 minutes
of cooking was programmed.
After the program is confirmed, cooking starts
and the audible alarm is automatically activated.
Cooking will end when "End-of-Cooking
Time = Current Time".
To display the program set, briefly press and
release the knob and the hands and icons will
show the program set.
At the end of cooking, the
the alarm beeps. After 1 minute, the alarm is
disabled and the
until you press the knob.
To cancel the program before the end, press the
button for 3 seconds: the program will be
cancelled and the timer returns to manual
cooking mode.
FCO 86 H / FCO 82 H
icon flashes.
icon
icon flashes and
icon continues flashing
Programming the "Start-of-cooking time"
and "End-of-cooking time"
Program "Start-of-cooking time" allows you to
start and end cooking automatically based on
the times programmed.
To program the "Start-of-cooking time", briefly
press the knob 1 time until the
flashing.
To increase or decrease the start-of-cooking
time in 1-minute intervals, turn the knob
clockwise orcounter-clockwise and the minute
hand moves 1 minute clockwise or counter-
clockwise.
The
icon will continue to flash for
10 seconds after the last turn. If, within this time,
you do not turn or press the knob, the hands
automatically return to displaying the time and
the program is cancelled. If you press the knob,
the "Start-of-cooking time" is stored (the
icon turns steady on), so long as you have
programmed at least 1 minute of delay, and
goes to setting the "End-of-cooking time"
(the
icon goes from off to flashing).
To program the "End-of-cooking time", follow
the procedure in the related paragraph.
Cooking will start when "Start Time = Current
Time".
Programming the "Minute Minder"
Programming the "Minute Minder" gives you
a simple alarm at the end of the programmed
time without activating cooking ("Minute
Minder" mode).
To schedule an "Alarm" without cooking
("Minute Minder mode"), briefly press the knob
3 times until the
knob, and the setting of the "Minute Minder" is
the same as the "End-of-cooking time" (see
corresponding paragraph).
The "Minute Minder" can only be used when
there is no program running.
Displaying the program set
The programmer allows the display of the
program set.
To view the program set, briefly press and
release the knob and the controller displays the
program set, moving the hands to the time set
and highlighting the steps with the flashing of
the related icons.
The controller will automatically return to
displaying the current time and continues
running the program set.
12
icon starts
icon flashes. Then, turn the
Publicidad
