Pioneer PDP-508XG Manual De Instrucciones página 45

Using with other equipment
Item Description
Always Output Outputs composite video and audio signals no matter
which input source is selected
INPUT 1 Prohibit Does not output composite video and audio signals
when "INPUT 1" is selected
INPUT 2 Prohibit Does not output composite video and audio signals
when "INPUT 2" is selected
INPUT 3 Prohibit Does not output composite video and audio signals
when "INPUT 3" is selected
INPUT 4 Prohibit Does not output composite video and audio signals
when "INPUT 4" is selected
INPUT 5 Prohibit Does not output composite video and audio signals
when "INPUT 5" is selected
INPUT 6 Prohibit Does not output composite video and audio signals
when "INPUT 6" is selected
5 Press HOME MENU to exit the menu.
Note
• The INPUT 4 and INPUT 5 video signals are not output from the
MONITOR OUT jack regardless of this setting.
Using the HDMI Input
The INPUT 3, INPUT 4 and INPUT 5 terminals are HDMI terminals
to which digital video and audio signals can be input. To use the
HDMI terminals, activate the terminal and specify the types of
video and audio signals to be received from the connected
equipment. For the types of these signals, see the operation
manual that came with the connected equipment.
Before starting the menu, press INPUT 3, INPUT 4 or INPUT 5 on
the remote control unit or press INPUT on the plasma television to
select "INPUT 3", "INPUT 4" or "INPUT 5".
Video signals supported
720 (1440) x 576i@50 Hz
720 x 576p@50 Hz
1280 x 720p@50 Hz
1920 x 1080i@50 Hz
720 (1440) x 480i@59.94 Hz/60 Hz
720 x 480p@59.94 Hz/60 Hz
1280 x 720p@59.94 Hz/60 Hz
1920 x 1080i@59.94 Hz/60 Hz
1920 x 1080p@24 Hz
1920 x 1080p@50 Hz
1920 x 1080p@60 Hz
PC signals supported
640 x 480 (VGA) 60 Hz
800 x 600 (SVGA) 60 Hz
1024 x 768 (XGA) 60 Hz
1360 x 768 (Wide - XGA) 60 Hz
1280 x 1024 (SXGA) 60 Hz
For audio, the system supports the following:
• Linear PCM (STEREO 2ch)
• Sampling frequency: 32 kHz, 44.1 kHz, 48 kHz
HDMI Control supported
The plasma television supports the HDMI Control functions. By
connecting devices that support the HDMI Control functions to the
plasma television, you can control the connected device(s) from
the plasma television or remote control unit of the plasma
television. See Using the HDMI Control on Chapter 11.
Deep Color supported
Deep Color means the color depth that describes the number of
bits used to represent the color of a single pixel in a bitmapped
image. Besides the conventional RGB/YCbCr16 bit/20 bit/24 bit
signals, the plasma television also supports RGB/YCbCr30 bit/36
bit signals. This enables finer, minute color reproduction when a
device that supports Deep Color signals is connected to the
plasma television. When Deep Color signals are received, the color
depth appears on the channel display.
Note
• It may take a short while until the image is displayed,
depending on the equipment connected.
• Make sure to use an HDMI compliant cable.
• When inputting 1080p signals, we recommend you use an
HDMI cable that supports HDMI Category 2.
• When connecting a PC to the HDMI terminal, use the HDMI
compliant PC or video card.
• When connecting a PC to the HDMI terminal using a DVI
output terminal, the plasma television may not display
properly. If that is the case, consult with your PC manufacturer.
• PC picture and/or sound may not be displayed or heard
properly depending on the PC used.
10
45
En