EINHELL GC-BC 25/1 I AS Manual De Instrucciones Original página 25

•
Retighten the lock nut.
9.6 Setting the idling speed
Important. Set the idling speed when the equip-
ment is warm.
If the engine stalls when the throttle is not
pressed and you have ruled out all the other cau-
ses listed in section 11 Troubleshooting, the idling
speed must be adjusted. To do this turn the idling
speed screw (Fig. 13b/Item E) clockwise until the
equipment runs smoothly at idling speed. If the
idling speed is so fast that the cutting tool turns
as well, it has to be reduced by turning the idling
speed screw for as long as is required for the cut-
ting tool to stop turning as well.
9.7 Applying grease to the gear unit
After every 20 hours of use add a little gear gre-
ase (approx. 10 g.) at the lubrication nipple (Fig.
28/Item 21).
10. Cleaning, storage, transport and
ordering of spare parts
10.1 Cleaning
•
Keep the handles free of oil so that you can
maintain a firm grip.
•
Clean the equipment as required with a damp
cloth and, if necessary, mild washing up
liquid.
Important!
Always pull out the spark boot plug each time
before carrying out any cleaning. Never immerse
the equipment in water or other liquids in order to
clean it.
Store the equipment in a safe and dry place out of
the reach of children.
10.2 Storage
Important: Never put the equipment into storage
for longer than 30 days without carrying out the
following steps.
Storing the equipment
If you intend to store the equipment for longer
than 30 days, the equipment must be prepared
accordingly. Otherwise the fuel still remaining in
the carburetor will evaporate and leave a rubbery
sediment. This can cause problems when starting
up the equipment and may require expensive
repairs.
Anl_GC_BC_25_1_I_AS_SPK9.indb 25 Anl_GC_BC_25_1_I_AS_SPK9.indb 25
GB
1. Slowly remove the fuel tank cap to release
any pressure that may have formed in the
tank. Carefully empty the tank.
2. To remove the fuel from the carburetor, start
the engine and let it run until it stops.
3. Leave the engine to cool (approx. 5 minutes).
4. Remove the spark plug (see section 9.4).
5. Add one teaspoon of 2-stroke engine oil into
the combustion chamber. Slowly pull the star-
ter cord several times to apply a layer of oil
to all internal components. Fit the spark plug
again.
Note: Store the equipment in a dry place and
far away from possible ignition sources such as
an oven, a gas-fi red hot water boiler, a gas-fi red
dryer, etc.
Putting the equipment back into operation
1. Remove the spark plug (see section 9.4).
2. Quickly tug on the starter cord to remove ex-
cess oil from the combustion chamber.
3. Clean the spark plug and check that the
electrode gap is correct, or insert a new spark
plug with the correct electrode gap.
4. Prepare the equipment for operation.
5. Fill the tank with the relevant mixture of fuel
and oil. See the section „Fuel and oil".
10.3 Transport
To transport the machine, empty the petrol tank
as described in section 10. Clean coarse dirt off
the equipment with a brush or hand brush. Dis-
mantle the drive rod mechanism as described in
section 5.2.
10.4 Ordering spare parts
Please provide the following information on all
orders for spare parts:
•
Model/type of the equipment
•
Article number of the equipment
•
ID number of the equipment
•
Part number of the required spare part
For our latest prices and information please go to
www.Einhell-Service.com
- 25 -
14.09.2023 10:38:55 14.09.2023 10:38:55