Stiga PARK PRO 340 IX Manual De Instrucciones página 116

The engine may be very warm immediately after
it is shut off. Do not touch the exhaust or adjacent
parts. This can cause burn injuries.
5.6. AFTER USE
• Allow the engine to cool before storing in an enclosed space.
• Clean (par. 6.3).
whenever the machine is left unattended, the operator leaves
the driving seat or parks the machine:
1. Stop the machine.
2. bring the cutting means assembly to the lowest height
position.
3. Make sure that all moving parts have come to a com-
plete stop.
4. Remove the ignition key.
6. MAINTENANCE
The safety regulations to be followed are described in chapter
1. Strictly comply with these instructions to avoid serious
risks or hazards:
Before c ommencing a ny i nspections, c leaning o r m aintenance/
adjustments on the machine:
• Disengage the cutting means.
• Stop the machine.
• Shift into neutral.
• Engage the parking brake.
• Stop the engine.
• Make sure that any moving component has stopped.
• Remove the ignition key.
• Use suitable clothing, protective gloves and goggles.
IMPORTANT Never leave the key inserted or within reach of
children or unauthorized people.
6.1. REFUELLING
The transparency of the window (17:A) of the tank makes it
easy to check the level. Do not fill the tank completely so that,
when the petrol heats up, it can expand without overflowing.
IMPORTANT Use only unleaded petrol. Do not mix petrol
with oil.
IMPORTANT Do not drip petrol onto the plastic parts to
avoid ruining them. In the event of accidental leaks, rinse im-
mediately with water. The warranty does not cover for damage
to plastic parts of the bodywork or the engine caused by petrol.
6.2. CHECK AND TOP-UP ENGINE OIL
IMPORTANT Observe the precautions provided in the en-
gine owner's manual.
Always check the oil level before use.
Mod. Honda GXV 630; 660; 690 (18):
1. Clean around the dipstick. Unscrew and remove it.
2. Clean the rod.
3. Insert the rod completely, without screwing it in position.
4. Remove the rod again.
5. Check the oil level.
6. If the level is low, top up to the "FULL" mark.
Mod. B&S 8270; B&S VANGUARD 18HP (19 and 20):
1. Clean around the dipstick.
2. Unscrew and remove it.
3. Clean the rod.
4. I nsert the rod completely and screw it in position.
5. U nscrew and remove the rod again.
6. Check the oil level.
7. I f the level is low, top up to the "FULL" mark.
6.3. CLEANING
• General instructions
Before each use, clean thoroughly following the instructions
below:
• Do not spray water onto the motor and electrical
components and prevent them from getting wet.
• Remove grass debris and mud accumulated inside the
chassis.
• Always make sure the air intakes are free of debris.
• Do not use aggressive liquids to clean the chassis.
• To reduce the risk of fire, keep the engine free of grass,
leaves residues or excessive grease.
1. Clean the engine cooling air intake (18:A).
2. After cleaning with water, start the machine and the and
the cutting means assembly installed on it to remove the
water that may otherwise infiltrate in the bearings and
cause damages.
6.4. BATTERY
Carefully read and observe the battery recharging instructions
in the booklet provided with the battery. Failure in following
the procedure or in charging the battery could permanently
damage the battery elements. A flat battery must be recharged
as soon as possible.
Charge through the engine:
1. In the case of a new battery, connect the cables to
the battery.
2. Take the machine outdoors.
3. Start the engine according to the instructions in this
manual.
4. Leave the engine running continuously for 45 minutes
(time needed to fully charge the battery).
5. Stop the engine.
Charging by battery charger.
IMPORTANT Recharging must be done using a battery
charger at constant voltage. Other recharging systems can irre-
versibly damage the battery.
6.5. CUTTING MEANS MAINTENANCE
Do not touch the cutting means until the ignition
key has been removed and the cutting means is
completely stationary. Be careful that the cutting
means can move, even if the key has been
removed (for battery-powered models).
All work on the cutting means (disassembly,
sharpening, balancing, repairing, reassembly
and/or replacing) are demanding jobs that require
special skills as well as special tools; For safety
reasons, these jobs are best carried out at a
Authorised Service Centre.
EN - 7