Publicidad
Idiomas disponibles
Idiomas disponibles
(pZ60S°ON)
21
To enjoy higher quality
tone:
1.
2.
%
8.
22
Connect stereo amplifier @ and
front speakers @ to your TV.
Turn your TV ON, and press
=<,
(Volume -/+) button
to set the volume to the
lowest setting.
Press (@/?) (Picture/sound)
button twice to display the
SOUND MENU.
F Press
(A) or)
menu
button to select "«@MODE"
(speaker mode).
Press ( — ) or(+_) menu
button to select OFF.
Sound stops being output from the
TV speakers.
* To output sound from the TV
speakers, select ON.
NOLOF cs seisstisssccbisceetacstedeccassiovecdsacests
* If ""@ MODE" (Speaker mode) is set
to OFF, sound will no longer be output
from the headphones connected to
your TV.
. Press (@/?) (Picture/sound)
button.
Speaker mode selection is
complete.
. Turn your audio amplifier ON,
and return the volume of your
audio amplifier to the normal
setting.
NONGE oo cicvsteiecientsntvecvassacsobsaccancaveases
* Take care not to set the volume of
your audio amplifier too high as this
may damage your speakers.
Press <1,
(Volume -/+)
button to adjust the volume.
The settings are complete.
To enjoy Dolby Pro Logic
Surround:
1.
Connect audio amplifiers and
speakers to the TV.
Select the desired connection
method from the following choices,
and connect audio amplifiers and
speakers to the TV.
[Al Connect stereo amplifier @ and
surround speakers @. This
leaves out the centre speaker.
(B): Connect stereo amplifiers @,
©, front speakers @, and
surround speakers @. This
uses the TV speakers as the
centre speakers.
[Ci Connect stereo amplifiers @,
©, stereo amplifier (or
monaural amplifier) ©, front
speakers @, surround speakers
@, and centre speaker ©.
if you use this method, do not
output sound from the TV
speakers.
. Turn your TV ON, and press
cx,
(Volume -/+) button
to set the volume to the
lowest setting.
Press SURO) (Surround)
button.
The DIGITAL SURROUND MENU
appears.
Press
or (4) menu
button to select DOLBY PRO
LOGIC.
Press
(Picture/sound)
button three times.
The mode setting menu appears.
DOLBY
PRO
LOGIC
CENTRE
MODE)
PHANTOM
NORMAL
WIDE
@@
MODE)
L.R.
CENTRE
OFF
'2
6°
€B:0K G:EXxIT
Press
or) menu
button to select the items,
and press ( — ) or
menu button to change the
settings.
6.
N
Method
CENTRE MODE
|s@ MODE
Al
PHANTOM
L. R.
|B;
NORMAL
CENTRE
NORMAL
[C;
OFF
* Use this mode when using a full-range
speaker as the centre speaker.
Frequencies of 100 Hz or lower are
output from the centre speaker to give
Dolby Surround an even greater impact.
Press ©, (Display) button
twice.
The speaker level setting menu
appears.
DOLBY
PRO
LOGIC
vAEST MODE
Turn your audio amplifiers
ON, and return the volume of
your audio amplifiers to the
normal setting.
* Take care not to set the volume of
your audio amplifiers too high as this
may damage your speakers.
Test signals alternate between the
speakers.
10. Press C—) or(#$_)
menu button to adjust the
level of each of the speakers
so that their volumes are the
same at the listening
position.
L,R:
Front speaker L, R
C*:
Centre speaker
S:
Surround speakers
* When CENTRE MODE is set to
PHANTOM, the volume of C: (Centre
speaker) cannot be adjusted.
NOUS sods cccicscctarseadeiteat
lease inndsedecaiucs
* If the volume of all speakers is not the
same even if the volume level is
adjusted, adjust the volume of your
audio amplifiers.
Sean enenevenuareuanennpssaveunesceuavocuanancezascnsen
11. Press & (Display) button
twice.
The setting are complete.
NALXS62-
in)
Bs
Publicidad
