Shaft Seal Replacement; Pump Disassembly - Pentair VS2 Guia De Instalacion

17
SERVICING
Always disconnect power to the VS2 Variable Speed Pump at the circuit breaker and disconnect the
communication cable before servicing the pump. Failure to do so could result in death or serious injury to
service people, users or others due to electric shock. Read all servicing instructions before working on the pump.
DO NOT open the strainer pot if pump fails to prime or if pump has been operating without water in the strainer pot.
Pumps operated in these circumstances may experience a build up of vapor pressure and may contain scalding hot
water. Opening the pump may cause serious personal injury. In order to avoid the possibility of personal injury, make sure the suction and
discharge valves are open and strainer pot temperature is cool to touch, then open with extreme caution.
Be sure not to scratch or mar the polished shaft seal faces; seal will leak if faces are damaged. The polished and lapped
faces of the seal could be damaged if not handled with care.
Electric Motor Care
Protect from heat
1. Shade the motor from the sun.
2. Any enclosure must be well ventilated to prevent
overheating.
3. Provide ample cross ventilation.
Protect against dirt
1. Protect from any foreign matter.
2. Do not store (or spill) chemicals on or near the motor.
3. Avoid sweeping or stirring up dust near the motor while
it is operating.
4. If a motor has been damaged by dirt it may void the motor
warranty.
5. Clean the lid and clamp, O-ring, and sealing surface of the
pump pot.
Protect against moisture
1. Protect from splashing or sprayed water.
2. Protect from extreme weather such as flooding.
3. If motor internals have become wet - let them dry before
operating. Do not allow the pump to operate if it has been
flooded.
4. If a motor has been damaged by water it may void the
motor warranty.

Shaft Seal Replacement

The Shaft Seal consists primarily of two parts, a rotating
member and a ceramic seal.
The pump requires little or no service other than reasonable
care, however, a Shaft Seal may occasionally become
damaged and must be replaced.
Note: The polished and lapped faces of the seal could be
damaged if not handled with care.
DO NOT run the pump dry. If the pump is run dry, the mechanical seal will be damaged and the pump will start leaking.
If this occurs, the damaged seal must be replaced. ALWAYS maintain proper water level. If the water level falls below
the suction port, the pump will
draw air through the suction port, losing the prime and causing the pump to run dry, resulting in a damaged seal. Continued operation
in this manner could cause a loss of pressure, resulting in damage to the pump case, impeller and seal and may cause property damage
and personal injury.

Pump Disassembly

All moving parts are located in the rear sub-assembly of
this pump.
Tools required:
• 1/4 inch socket or open end wrench.
• 3/8 inch socket or open end wrench.
• 9/16 inch open end wrench.
• 1/4 inch Allen Key
• Flat blade screwdriver.
To remove and repair the motor subassembly, follow the
steps below:
1. Press the Start/Stop button to stop the pump and turn
off the pump circuit breaker at the main panel.
2. Drain the pump by removing the drain plugs.
3. Remove the 4 bolts that hold the main pump body
(strainer pot/volute) to the rear sub-assembly.
4. GENTLY pull the two pump halves apart, removing the
rear sub-assembly.
5. Remove the three hex head screws holding the diffuser
in position.
6. Hold the impeller securely in place and remove the
impeller lock screw by using a flat blade screwdriver or
wrench. The screw is a left-handed thread and loosens
in a clockwise direction.
7. To unscrew the impeller from the shaft, insert a 1/4 inch
Allen key into the center of the motor fan cover and
twist the impeller counter-clockwise.
8. Remove the four bolts from the seal plate to the motor
using a 9/16 inch wrench.
9. Place the seal plate face down on a flat surface and tap
out the ceramic seal.
10. Clean the seal plate, seal housing, and the motor shaft.