Kärcher BD 75/120 R Classic Bp Manual página 10

Malfunction
The bar of the filling level display is
flashing, "fresh water empty" display
The suction performance is too low
The cleaning results are unsatisfacto-
ry
The brushes do not rotate
The device does not brake
The waste water drain hose is clogged 1. Open the dosing unit cover at the drain hose.
Warranty
The warranty conditions issued by our sales company
responsible apply in all countries. We shall remedy pos-
A: Packaging unit, B: Quantity required by the device
Description
Disc brush, red (medium, standard)
Disc brush, red (medium, standard)
Disc brush, natural colour (soft)
Disc brush, white
Disc brush, black (hard)
Fine diamond pad, green
Coarse diamond pad, white
Medium diamond pad, yellow
Pad drive board
Suqeegee,1000mm, V-shape
Suction lip set, PU(Oil-proof), transparent
General
Driving / cleaning speed
Transport speed
Travel speed, backwards
Theoretical surface performance
Theoretical surface performance with side scrubbing deck
Practical surface performance
Fresh water tank capacity
Waste water tank capacity
Water dosage
Load per unit area (with driver and full fresh water tank)
Surface pressure
Load per unit area (weight / parking area)
Dimensions
Length
Width
Wide suction bar
Height
Working width
Packaging dimensions lxwxh
Turning circle
Battery compartment dimensions lxwxh
Tyres
10
Rectification
1. Refill the fresh water tank.
1. Clean the seals between the waste water tank and the cover, check for leaks and replace if necessary.
2. Check the fluff filter for soiling and clean if necessary.
3. Clean the suction lips at the suction bar, turn over or replace if necessary.
4. Close the lid on the waste water drain hose.
5. Close the cover of the waste water tank rinsing system.
6. Check the suction hose for clogging and clean if necessary.
7. Check the suction hose for leaks and replace if necessary.
8. Check the adjustment of the suction bar.
1. Set the appropriate cleaning program for the cleaning task.
2. Use suitable brushes for the cleaning task.
3. Use a suitable detergent for the cleaning task.
4. Reduce the driving speed.
5. Adjust the contact pressure.
6. Adjust the squeegee blades.
7. Check the brushes for wear and replace if necessary.
8. Check the water output.
1. Reduce the contact pressure.
2. Check if the brushes are blocked by a foreign body and remove the foreign body if necessary.
3. If the motor is overloaded, let the motor cool down.
4. Set the programme switch to "OFF".
5. Wait 10 seconds.
6. Set the program switch to the desired program.
7. Check that the plug of the device is plugged into the cleaning head.
1. Undo the brake lock (see "Operation / Pushing the device").
2. Pull the suction hose off the suction bar and close it by hand.
3. Set the programme switch to "Vacuum".
The blockage is sucked out of the drain hose into the waste water tank.
sible malfunctions on your device within the warranty
period free of cost, provided that a material or manufac-
turing defect is the cause. In a warranty case, please
Cleaning head with disc brushes accessories
D 75
Part no.
9.753-239.0
4.905-018.0
4.905-020.0
4.905-019.0
4.905-021.0
6.371-236.0
6.371-252.0
6.371-253.0
4.762-447.0
9.753-441.0
9.753-249.0
Technical data
Accessories
Description
For cleaning lightly soiled or sensitive floors.
For cleaning lightly soiled or sensitive floors.
For polishing floors.
For polishing and maintenance cleaning of sensitive floors.
For cleaning heavily soiled floors.
For refreshing lime-containing coverings and epoxy resin-coated floors.
For holding pads.
km/h
km/h
km/h
2
m /h
2
m /h
2
m /h
l
l
l/min
2
N/mm
2
kg/m
mm
mm
mm
mm
mm
mm
mm
mm
English
contact your dealer (with the purchase receipt) or the
next authorised customer service site.
(See overleaf for the address)
BD 75/120 R Classic Bp
6
6
4
4500
-
3150
125
120
0-5
0,64
563
1660
1035
1000
1480
750
1715x1140x1625
1750
620x420x370