EINHELL GE-CM 18/30 Li Manual De Instrucciones Original página 40

5. Before starting the equipment
The lawn mower is delivered partly assembled.
The push bar and the grass basket must be as-
sembled before using the lawn mower. Follow the
instructions step by step and refer to the pictures
when assembling.
Important! Required assembly parts (screws,
cable guides, etc.) or functional parts (e.g. plugs,
wrenches, etc.) can be found in the molded parts
of the packaging or on the equipment.
Warning! Always pull out the safety plug befo-
re making adjustments to the equipment.
Fitting the push bar (Fig. 3a to 3c)
Take a bottom push bar (Fig. 2 /Item 3) and fasten
it with the nut (Fig. 2/Item 13) as shown in Fig. 3a.
Proceed in the same way on the other side. Screw
the top push bar (Fig. 2/Item 2) to the bottom push
bar (Fig. 2/Item 3) as shown in Fig. 3b.
Then attach the power cable to the push bar (Fig.
2/Item 14) using the cable clips (Fig. 3c).
Make sure that the cable and cable clips do not
obstruct the push bar when it is fl ipped over (see
section 8).
Mounting the grass basket (Fig. 4a to 4c)
Plug the bottom and the top part of the grass box
together (Fig. 4a/Item 9, 10). Ensure that all the
plastic lugs engage correctly. Next push the grass
box handle (Fig. 4b/Item 11) into the openings on
the grass box. Check that the handle is secure
and correctly positioned. Before you fi t the grass
basket you must ensure that the motor is switched
off and the blade is not rotating.
The grass box must be attached to the two hooks
on the mower. To do this, open the ejector fl ap
with one hand (Fig. 4c/Item 7) and attach the
grass box with the other hand. The ejector fl ap is
held against the grass box by a spring.
Adjusting the cutting height
Warning!
Adjust the cutting height only when the motor has
been switched off and the safety plug has been
disconnected.
Before you begin to mow, check to ensure that the
blade is not blunt and that none of the fasteners
are damaged. To prevent any imbalance, replace
Anl_SA_GE_CM_18_30_Li.indb 40 Anl_SA_GE_CM_18_30_Li.indb 40
GB
blunt and/or damaged blades. To carry out this
check, fi rst switch off the motor and pull out the
safety plug.
The cutting height is adjusted as shown in Figure
5. To do so, turn the equipment upside down or tilt
it to the side. Position both the front and rear axle
in the same notch, so that the cutting blade runs
parallel to the lawn.
Position Cutting depth
1 70mm
2 50mm
3 30mm
Charging the battery (Fig. 6)
1. Take the battery pack out of the equipment.
Do this by pressing the side pushlock buttons.
2. Check that your mains voltage is the same as
that marked on the rating plate of the battery
charger. Insert the power plug of the charger
(17) into the socket outlet. The green LED will
then begin to fl ash.
3. Insert the battery pack (16) into the battery
charger (17).
4. In the section entitled „Charger indicator" you
will fi nd a table with an explanation of the LED
indicator on the charger.
The battery pack can become a little warm during
the charging. This is normal.
If the battery pack fails to charge, check:
•
whether there is voltage at the socket outlet
•
whether there is good contact at the charging
contacts
If the battery pack still fails to charge, send
•
the charging unit
•
and the battery pack
to our customer service center.
To ensure that items are properly packaged
and delivered when you send them to us,
please contact our customer service or the
point of sale at which the equipment was
purchased.
When shipping or disposing of batteries and
cordless tools, always ensure that they are
packed individually in plastic bags to prevent
short circuits and fi res.
To ensure that the battery pack provides long ser-
vice, you should take care to recharge it promptly.
You must recharge the battery pack when you
- 40 -
28.02.2024 10:52:52 28.02.2024 10:52:52