Intended Use - DeWalt DCN21PL Manual De Instrucciones

Pistola de clavos para enmarcado en plástico 21 inalámbrica 20 v máx
Ocultar thumbs Ver también para DCN21PL:
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

b. Check to see if receptacle is connected to a light
switch which turns power off when you turn out the
lights;
c. Move the charger and battery pack to a location
where the surrounding air temperature is
approximately 65 °F – 75 °F (18 ° – 24 °C);
d. If charging problems persist, take the tool, battery
pack and charger to your local service center.
4. The battery pack should be recharged when it fails to
produce sufficient power on jobs which were easily
done previously. DO NOT CONTINUE to use under these
conditions. Follow the charging procedure. You may
also charge a partially used pack whenever you desire
with no adverse effect on the battery pack.
5. Foreign materials of a conductive nature such as, but
not limited to, grinding dust, metal chips, steel wool,
aluminum foil, or any buildup of metallic particles
should be kept away from charger cavities. Always
unplug the charger from the power supply when there
is no battery pack in the cavity. Unplug the charger
before attempting to clean.
6. Do not freeze or immerse the charger in water or any
other liquid.
Storage Recommendations
1. The best storage place is one that is cool and dry, away
from direct sunlight and excess heat or cold.
2. For long storage, it is recommended to store a fully
charged battery pack in a cool dry place out of the
charger for optimal results.
nOTE: Battery packs should not be stored completely
depleted of charge. The battery pack will need to be
recharged before use.
SAVE THESE INSTRUCTIONS FOR
FUTURE USE
COMPONENTS (FIG. A)

WARNING: Never modify the power tool or any part
of it. Damage or personal injury could result.
Refer to Figure A at the beginning of this manual for a
complete list of components.

Intended Use

The DCN21PL cordless framing nailer has been designed for
driving nails into wooden workpieces.
DO nOT use under wet conditions or in presence of
flammable liquids or gases.
This cordless framing nailer is a professional power tool.
DO nOT let children come into contact with the tool.
Supervision is required when inexperienced operators use
this tool.
NOTICE: NEVER spray or in any other way apply
lubricants or cleaning solvents inside the tool. This
can seriously affect the life and performance of
the tool.
TOOL SPECIFICATIONS
Firing mode
Selective: Bump or Sequential
Voltage
Height
Width
Length
Weight
Magazine angle
Loading capacity
NAIL SPECIFICATIONS
Nail lengths
2" – 3-1/4" (50 mm – 83 mm)
Shank diameters
0.113" – 0.148" (2.8 mm – 3.3 mm)
Nail stick angles
Shank types
OPERATION

WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start-up can cause injury.
Installing and Removing the Battery Pack
(Fig. D)
nOTE: For best results, make sure your battery pack is
fully charged.
To install the battery pack 
 12 
battery pack with the rails inside the tool's handle and slide
it into the handle until the battery pack is firmly seated in
the tool and ensure that it does not disengage.
To remove the battery pack from the tool, press the release
button 
 25 
and firmly pull the battery pack out of the tool
handle. Insert it into the charger as described in the charger
section of this manual.
Fig. D
12
English
20
16.5" (419 mm)
4" (104 mm)
13.25" (335 mm)
8.5 lbs (3.85 kg)
21°
Up to 49 nails
Full Round Head
21°
Smooth and Ring
into the tool handle, align the
25
9

Publicidad

Tabla de contenido
loading

Tabla de contenido