Yamaha DSP-AZ2 Manual De Instrucciones página 35

Notes
• The DTS 96/24 decoder and the DTS ES decoder cannot be
activated at the same time while playing the DTS 96/24 signal.
When "AUTO" is selected, the DTS 96/24 decoder has
precedence over the DTS ES decoder.
• 6.1-channel playback is not possible even if EX/ES is pressed
in the following cases:
– When "1C REAR L/R SP"is set to "NONE".
– When the sound effect is turned off.
– When the source connected to the 6CH INPUT jack is
being played.
– When the source being played does not contain rear L/R
channel signals.
– When Dolby Digital KARAOKE source is being played.
– When headphones are connected.
– When "8ch Stereo" is selected.
• When the power of this unit is turned off, the input mode
will be reset to AUTO.
I Virtual CINEMA DSP
With the Virtual CINEMA DSP, you can enjoy all the
DSP programs without rear speakers. It creates the virtual
speakers to reproduce the natural sound field.
The sound field processing is changed to the Virtual
CINEMA DSP mode according to the selected DSP
program by setting "1C REAR L/R SP" on the SET
MENU to NONE.
Notes
• This unit is not set in the virtual CINEMA DSP mode even if
"1C REAR L/R SP" is set to NONE in the following cases:
– when the 8ch Stereo, DOLBY DIGITAL Normal, Pro Logic
Normal, Pro Logic , DTS Normal or Neo: 6 program is
selected;
– when the sound effect is turned off;
– when 6CH INPUT is selected as the input source;
– when using the test tone; or
– when connecting the headphones.
• When over 48 kHz sampling digital signal is being input, this
unit reproduces sound in the virtual CINEMA DSP mode after
converting the sampling frequency to 48 kHz or below.
I SILENT CINEMA DSP
You can enjoy the powerful sound field as if there were
actual speakers with the SILENT CINEMA DSP. You can
listen to SILENT CINEMA DSP by connecting your
headphones to the PHONES jack while the digital sound
field processor is on. Enjoy all the DSP program using the
headphones. The "SILENT" indicator lights up on the
front panel display. (If the sound effect is off, you listen to
the source with normal stereo reproduction.)
Notes
• When 6CH INPUT is selected as the input source, this unit is
not set in the SILENT CINEMA DSP mode even if the sound
effect is on.
• When over 48 kHz sampling digital signal is being input, this
unit reproduces sound in the CINEMA DSP mode after
converting the sampling frequency to 48 kHz or below.
I Normal Stereo Reproduction
Press STEREO/EFFECT to turn off the sound
effect for normal stereo reproduction.
Press STEREO/EFFECT again to turn the sound
effect back on.
STEREO
EFFECT
Front panel
Notes
• If "1B MAIN SP" on the SET MENU is set to "SMALL" and
"1E LFE/BASS OUT" is set to "SWFR", or "1E LFE/BASS
OUT" is set to "BOTH", the LFE signals will be output from
the subwoofer.
• If you turn off the sound effect while a Dolby Digital or DTS
signal is being output, the dynamic range of the signal is
automatically compressed and the sounds of the center and rear
speaker channels are mixed and output from the main speakers.
• The volume may be greatly reduced when you turn off the
sound effect or if you set "11 D-RANGE" on the SET MENU
to MIN. In this case turn on the sound effect.
I Displaying the information about
the input source
During the stereo reproduction, you can display the
information such as the type, format and sampling
frequency of the signal input from the component
connected to this unit.
(During playback)
1
Set PARAMETER/SET
MENU to PARAMETER.
2
Press k/n to display the information about
the input signal.
ON SCREEN LEVEL
SLEEP TEST
BASIC PLAYBACK
STEREO
or
EFFECT
Remote control
PARAMETER
SET MENU
PARAMETER
SET MENU
33