How To Move The Machine - Hillyard Trident T30 SC PRO Manual De Uso

7. Grip the handle (3) and turn the recovery tank until it reaches the working position.
8. The machine is fixed to the pallet by means of chocks, which block the wheels and brush head; remove these chocks.
9. Insert the starter key and turn on the machine; turn the main switch to the "I" position by turning the key (2) a quarter turn clockwise (Fig.5).
10. Lift the brush head body and press the "BRUSH HEAD CONTROL" button (6) on the control panel (Fig.6).
N.B.: as soon as the button (6) on the control panel is pressed, the green LED (7) ("BRUSH HEAD BODY WORK POSITION") will switch
off (Fig.6).
11. Raise the squeegee body and turn the squeegee control lever (8) in the direction of the arrow (Fig.7). The lever is located on the back of the
machine.
12. Press the "REVERSE ACTIVATION - DEACTIVATION" button (9) on the control handlebars (Fig.8).
N.B.: As soon as the button (9) is pressed on the control panel, the "REVERSE ACTIVE" LED (10) on the control panel will be illuminated
(Fig.8).
13. Activate the dead man's lever (11) underneath the control handlebars (Fig.9) to start moving the machine in reverse.
14. Use a ramp to bring the machine down from the pallet.
CAUTION: do not fit the brush and the rear squeegee body before unloading the machine, and avoid any violent jolts to the brush head
and squeegee support.
N.B.: the ramp gradient must not be such as to cause damage to the machine as it comes down.
15. Turn off the machine and turn the key (2) a quarter turn anticlockwise (Fig.2). Remove the key from the instrument panel.
16. Grip the handle (3) and turn the recovery tank as far as it will go to the maintenance position (Fig.3).
17. Disconnect the pad battery connector (4) from the main system connector (5) (Fig.4).
ATTENTION: This process must be carried out by qualified personnel.
18. Grip the handle (3) on the right-hand side of the recovery tank and turn the tank until it reaches the work position.

HOW TO MOVE THE MACHINE

To transport the machine safely, proceed as follows:
DANGER: before starting any task, make sure the current regulations concerning the safe transport of dangerous substances are
scrupulously observed.
1. Check to make sure that the solution tank and the recovery tank are empty. If this is not the case, empty them (see the sections titled
"EMPTYING THE SOLUTION
2. Insert the key (2) into the main switch on the control panel. Move the main switch to the "I" position by turning the key (2) a quarter turn
clockwise (Fig.5).
3. Lift the brush head body and press the "BRUSH HEAD CONTROL" button (6) on the control panel (Fig.6).
N.B.: as soon as the button (6) on the control panel is pressed, the green LED (7) ("BRUSH HEAD BODY WORK POSITION") will switch
off (Fig.6).
4. Raise the squeegee body and turn the squeegee control lever (8) in the direction of the arrow (Fig.7). The lever is located on the back of the
machine.
5. When you push the dead man's lever (11) (Fig.9), the machine will begin to move.
6. Use a ramp to move the machine up onto the transport vehicle.
CAUTION: During this operation, check there are no people or objects near the machine.
N.B.: the ramp gradient must not be such as to cause damage to the machine as it goes up.
7. Position the machine on the means of transport, and move the main switch to the "0" position by turning the key (2) a quarter turn anti-
clockwise (Fig.2). Remove the key from the main switch.
8. Grip the handle (3) and raise the recovery tank to the maintenance position (Fig.3).
9. Disconnect the battery connector (4) from the main system connector of the machine (5) (Fig.4).
10. Grip the handle (3) and lower the recovery tank to its working position.
WARNING: secure the device according to the directives in force in the country of use, so that it cannot slide or tip over.
TANK" and "EMPTYING THE RECOVERY TANK").
13