Silent-Max Function; Automatic Detergent Dosing System (Hdc Versions); Vacuum Wand Kit - Hillyard Trident T30 SC PRO Manual De Uso

SILENT-MAX FUNCTION

This machine has a SILENT-MAX function for reducing the noise generated by the vacuum motor.
To activate or deactivate this function, simply press the button (19) on the instrument panel for at least three seconds (Fig.4).
N.B.: When the silent-max function is active, the relative LED (20) will light up on the control panel (Fig.4).

AUTOMATIC DETERGENT DOSING SYSTEM (HDC VERSIONS)

Upon request, the machine can be fitted with a system that measures out the detergent separately from the water in the solution tank.
To start it do as follows.
1. With the machine running, press the HDC SYSTEM ACTIVATION-DEACTIVATION switch (21) (Fig.11).
N.B.: if the LED on the switch (21) is on, the HDC system is active; if the LED is off, the HDC system is deactivated.
N.B.: the HDC system is activated when the electric pump in the machine water system starts up.
N.B.: if you want to deactivate the HDC system, press the switch (21) again.
N.B.: the amount of detergent present in the washing solution dispensed by the machine is proportional (in a percentage defined by a
parameter preset in the machine) to the water flow rate present in the water circuit of the machine.

VACUUM WAND KIT

On request, the machine can be equipped with the liquid vacuum wand; in order to use this, proceed as follows:
1. Make sure that the brush head body is in the rest position; if this is not the case, press the "BRUSH HEAD CONTROL" button (7) on the
control panel (Fig.4).
N.B.: When the brush head body is in the rest position, the green LED ("BRUSH HEAD BODY WORK POSITION") (8) will switch off
(Fig.4).
2. Turn off, turn the key (1) a quarter turn anticlockwise (Fig.12).
3. Lower the squeegee body and turn the squeegee control lever (3) in the direction of the arrow (Fig.5). The lever is located on the back of
the machine.
4. Open the storage compartment by turning the handle (22) (Fig.13).
5. Remove all the vacuum kit components from the storage compartment.
6. Assemble the steel extension tube (Fig.14).
7. Insert the vacuum brush (24) into the extension tube (23) (Fig.15).
8. Connect the wand kit vacuum tube (25) to the extension tube (26) (Fig.16).
9. Remove the squeegee vacuum tube (26) from the sleeve (27) in the squeegee body (Fig.17).
10. Connect the wand kit vacuum tube (23) to the squeegee vacuum tube (26) (Fig.18).
11. Turn on the machine and turn the key (1) a quarter turn clockwise (Fig.1).
12. Activate the vacuum control kit by pressing the button (28) (Fig.19).
N.B.: As soon as the button (28) is pressed, the LED on it will light up (Fig.19).
N.B.: As soon as the button (28) on the control display is pressed, the symbol for the vacuum wand kit will appear (Fig.20).
N.B.: With the vacuum wand kit active, the traction and work functions are deactivated.
WARNING: never pick up solid matter such as dust, cigarette stubs, paper, etc.
CAUTION: Never collect gases, explosive/inflammable liquids or powders, nor acids and solvents! These include gasoline, paint thinners
and fuel oil (which, when mixed with the vacuum air, can form explosive vapours or mixtures), and also non-diluted acids and solvents,
acetones, aluminium and magnesium powders. These substances may also corrode the materials used to construct the machine.
CAUTION: If the machine is used in dangerous areas (e.g. petrol stations), the relative safety standards must be observed. It is forbidden
to use the machine in environments with a potentially explosive atmosphere.
13. After completing the task, the wand kit can be fixed in the side support on the machine (Fig.21).
23