Hour Meter; Battery Charge Level Indicator; Scrubbing With Drying; Scrubbing Without Drying - Hillyard Trident T30 SC PRO Manual De Uso

6. Lower the squeegee body and turn the squeegee control lever (3) in the direction of the arrow (Fig.5). The lever is located on the back of
the machine.
7. When the dead man's lever (4) is pressed, the machine will begin to move. The lever is located underneath the control handlebars (Fig.6).
N.B.: the gearmotor will only begin functioning, and the solenoid valve will only begin dispensing detergent solution, when the brush head
body is in its working position.
8. During the first few metres, check that the detergent solution coming out is suitable for the task in hand. If it isn't, adjust it after reading the
section "REGULATING THE DETERGENT
The machine will now begin to work with full efficiency until the battery is flat or until the detergent solution has finished.
During the first few metres, check that there is sufficient solution and that the squeegee is drying correctly.
N.B.: If the dead man's lever is released during the scrubbing with drying operation, the brush motor and the solenoid valve will be
deactivated. The vacuum motor will continue working until the squeegee control lever is rotated to bring it back to its idle position.
N.B.: if the squeegee body is raised during the scrubbing and drying operation, the vacuum motor will continue working at maximum
speed for a certain period of time, and then switch off. This ensures that all the liquid in the vacuum tube is eliminated.
N.B.: when filling the solution tank, it is good practice to empty the recovery tank using the special drainage hose.

HOUR METER

The machine control panel contains the control display, which shows the total usage time (5) (Fig.3). The numbers before the "hourglass"
symbol identify tenths of an hour (a tenth of an hour corresponds to six minutes), while the other numbers identify the hours.

BATTERY CHARGE LEVEL INDICATOR

The machine instrument panel contains the control display. At the top right of the work screen, there is a graphic symbol (6) (Fig. 3) representing
the battery charge level indicator. The indicator is composed of 5 charge levels, each of which represents about 20% of residual charge. With a
residual charge of 20% the graphic symbol starts to flash and after a few second it will appear in larger dimensions in the middle of the screen,
under these conditions take the machine to the usual place to charge the batteries.
ATTENTION: a few seconds after the battery charge level reaches 20%, the brush motor switches off automatically. With the remaining
charge it is still possible, however, to complete the drying process before recharging
ATTENTION: a few seconds after the battery charge level reaches 10%, the vacuum motor switches off automatically. With the remaining
charge, it is still possible, however, to move the machine to the location designated for its recharging

SCRUBBING WITH DRYING

To perform a scrubbing and drying program, proceed as follows:
1. Make all the checks listed in
2. Go to the driving position, behind the machine.
3. Turn on the machine and turn the key (1) a quarter turn clockwise (Fig.1).
4. Lower the brush head body, press the "BRUSH HEAD CONTROL" button (7) on the control panel (Fig.4).
N.B.: As soon as the button (7) on the control panel is pressed, the green LED ("BRUSH HEAD BODY WORK POSITION") (8) will switch
on (Fig.4).
5. Lower the squeegee body and turn the squeegee control lever (3) in the direction of the arrow (Fig.5). The lever is located on the back of
the machine.
6. When the dead man's lever (4) is pressed, the machine will begin to move. The lever is located underneath the control handlebars (Fig.6).
N.B.: the gearmotor will only begin functioning, and the solenoid valve will only begin dispensing detergent solution, when the brush head
body is in its working position.
7. During the first few metres, check that the detergent solution coming out is suitable for the task in hand. If it isn't, adjust it after reading the
section "REGULATING THE DETERGENT

SCRUBBING WITHOUT DRYING

To perform a scrubbing only program, proceed as follows:
1. Make all the checks listed in
2. Go to the driving position, behind the machine.
3. Turn on the machine and turn the key (1) a quarter turn clockwise (Fig.1).
4. Lower the brush head body, press the "BRUSH HEAD CONTROL" button (7) on the control panel (Fig.4).
N.B.: As soon as the button (7) on the control panel is pressed, the green LED ("BRUSH HEAD BODY WORK POSITION") (8) will switch
on (Fig.4).
SOLUTION".
"PREPARING TO WORK".
SOLUTION".
"PREPARING TO WORK".
20