Audio Inputs And Outputs; Tuner Inputs; Video 1-6 Audio Inputs; Video Out Audio Output - Rotel RSP-1572 Manual De Instrucciones

20

Audio Inputs and Outputs

This Rotel processor provides both analog and digital audio
connections.

Tuner Inputs

d
A left/right pair of RCA analog audio inputs for connecting an AM/
FM tuner.
VIDEO 1–6 Audio Inputs
g
Six pairs of RCA inputs (VIDEO IN 1–6) provide connections for left/
right analog audio signals from six additional source components.
These inputs have corresponding video inputs and are used for VCRs,
satellite TV tuners, DVD players, etc. However, they may also be used for
additional audio only components, simply by omitting the corresponding
video connections.

VIDEO Out Audio Output

h
One pair of RCA jacks (VIDEO OUT) provide connections for sending line
level left and right analog audio signals for recording to a VCR.
This connection can be assigned to any analog audio connection.

CD Inputs

f
A left/right pair of RCA analog audio inputs for connecting a CD
player.

MULTI Inputs

j
A set of RCA inputs accept up to 7.1 channels of analog signals from
a DVD-A or SACD player. There are inputs for FRONT L & R, CENTER,
SUB, REAR L & R, and CENTER BACK 1 & 2 or FRONT VERTICAL
HEIGHT L & R in a Dolby PLIIz setup.
These inputs bypass all digital processing in the processor and are routed
directly to the Volume control and preamp outputs.
There are two subwoofer options for the MULTI input. Normally, the .1
channel input is passed through directly to the subwoofer output. An
optional bass redirect feature duplicates the seven main channels, sums
them, and sends this mono signal through a 100Hz analog low filter
to the subwoofer output. This provides an unaltered analog bypass for
the seven main channels along with a subwoofer signal derived from
those channels.

Preamp Outputs

k
A group of ten RCA analog audio outputs sends the RSP-1572's line
level output signals to external amplifiers and powered subwoofers.
These outputs are variable level, adjusted by the RSP-1572's volume
control. The ten connectors provide output for: FRONT L & R, CENTER 1
& 2, SURROUND (REAR) L & R, CENTER BACK CB1 & CB2(or FRONT
VERTICAL HEIGHT L & R), and SUBWOOFER 1 & 2.
Note: Depending on your system configuration, you may use some or all
of these connections. For example, if you only have one center channel,
connect it to the CENTER 1 output. If you only have one center back
channel, connect it to the CB1 output.
RSP-1572 SURROUND SOUND PROCESSOR

Digital Inputs

t
The RSP-1572 accepts digital inputs from source components such as CD
players, satellite TV tuners, and DVD players. The built-in digital processor
senses the correct sampling rates.
Note: With a digital input connection, the processor will be used to
decode the signal, rather than the source component's internal decoders.
You must use digital connections for a DVD player that supplies a Dolby
Digital or DTS signal; otherwise the processor will not be able to decode
these formats.
There are seven digital inputs on the rear panel, three coaxial and four
optical, as well as the HDMI Audio input that is carried by the HDMI
cables along with the digital video signals. These digital inputs can be
assigned to any of the input sources using the INPUT SETUP screen during
the setup process. For example, you can assign the COAXIAL 1 digital
input connector to the VIDEO 1 source and the OPTICAL 2 digital input
to the VIDEO 3 source. By default, the source input buttons are factory
configured to select the following inputs:
Digital Optical 1
CD:
Analog
Tuner:
Video 1: HDMI Audio (HDMI 1)
Video 2: HDMI Audio (HDMI 2)
Video 3: HDMI Audio (HDMI 3)
Video 4: HDMI Audio (HDMI 4)
Video 5: Digital Coaxial 1
Digital Optical 2
Video 6:
Note: When using digital connections, you may also want to make
the analog audio input connections described previously. The analog
connection is necessary to send an analog Video and Audio signal to
Zones 2, 3 & 4.

Digital Outputs

y
The RSP-1572 has two digital audio outputs (one coaxial and one
optical) to send the digital signal from any of the digital inputs to a digital
recorder or outboard digital processor. When a digital input source
signal is selected for listening, that signal is automatically sent to both
digital outputs for recording.
USB Audio Connection
4
Music storage devices can be accessed by the unit through this input. Music
storage devices such as MP3 players, iPod, iPhone, USB memory sticks or
any other form of memory devices with USB interface can be connected
to the unit through the front USB socket. The unit will automatically search
music files from the connected storage device.
Note: When connecting iPod or iPhone to the front USB, the controls
on the iPod/iPhone remain active. Only simple controls such as PLAY,
STOP, SKIP TRACK can be controlled by the RSP-1572.
The front USB can also accept a USB Bluetooth dongle (supplied). This
allows you to stream music from your Bluetooth device, i.e. mobile
phone. Insert the USB Bluetooth dongle into the front USB, the display
will show "READY" status. From your device (mobile phone etc..) activate
Bluetooth and allow it to search for other Bluetooth devices and it will
find "Rotel Bluetooth". Select "Rotel Bluetooth" and it will ask you to enter
a password. Enter "0000" and accept. The RSP-1572 will recognize a
device is attempting to connect to it, and will display this information on
the OSD. Press ENT key on the remote to accept. The "READY" status