Other Connections; Ac Input; Master Power Switch; 12V Trigger Connections - Rotel RSP-1572 Manual De Instrucciones

English
will change to "RUNNING" and you can start streaming music to the
RSP-1572.
Note: Not all Bluetooth dongles will operate with the unit. Please use
the dongle supplied by Rotel.

Other Connections

AC Input

;
Your Rotel processor is configured at the factory for the proper AC line
voltage in the country where you purchased it (USA: 120 volts/60Hz
AC or CE: 230 volts/50 Hz AC ). The AC line configuration is noted
on a decal on the back of your unit. Plug the supplied cord into the AC
INPUT receptacle on the back of the unit.
Note: Memorized settings and video labels are preserved indefinitely,
even if the unit is disconnected from AC power.

Master Power Switch

a
The large rocker switch on the rear panel is a master power switch. When
it is in the OFF position, power to the unit is completely off. When it is in
the ON position, the front panel STANDBY and remote control ON/OFF
buttons can be used to activate the unit or put it into standby mode.

12V TRIGGER Connections

o
Many Rotel amplifiers offer the option of turning them on and off using
a 12 volt trigger. These six connections provide this 12 volt trigger
signal from the processor. When the unit is activated, a 12 volt DC
signal is sent from these jacks to the amplifiers to turn them on. When
the processor is put in STANDBY mode, the trigger signal is interrupted
and the amplifiers turn off.
To use the remote turn on feature, connect one of the RSP-1572's 12V
TRIG OUT jacks to the 12 volt trigger input of a Rotel amplifier, using a
cable with mono 3.5mm mini-plugs on both ends. The +12 V DC signal
appears at the "tip" connector.
Note: The 12V Trigger outputs are configured to turn on in various
combinations only when specific input sources are activated. See the
INPUT SETUP and ZONE 2–4 SETUP menus in the Setup section of this
manual for details

REM IN Jacks

\
Four 3.5 mm mini-jacks (labeled EXT, ZONE 2, ZONE 3, and ZONE 4)
receive command codes from a third-party infrared receiver or Rotel remote
zone keypad, These remote IR inputs are used when the IR signals from a
hand held remote control cannot reach the front panel IR sensor.
EXT: The EXT jack is used with an outboard IR receiver to duplicate the
front panel IR sensor. This feature is useful when the unit is installed in a
cabinet and the front panel sensor is blocked or when IR signals need to
be relayed to other components.
ZONE: The ZONE 2, 3, or 4 jacks are used with IR repeater systems to
receive signals from IR control systems in remote locations. For example,
remote control signals sent to the ZONE 2 jack control the ZONE 2 features
of the RSP-1572 and can be relayed to other components.
Consult your authorized Rotel dealer for information on external receivers
and the proper wiring of 3.5mm mini-plugs to fit the REM IN jacks.
Note: The IR signals from the REM IN EXT and REM IN ZONE 2–4
jacks can be relayed to source components using external IR emitters or
hard-wired connections from the IR OUT jacks. See the following section
for additional information.

IR OUT Jacks

[
The IR OUT 1 & 2 jacks send IR signals received at the REM IN ZONE
2–4 jacks or the REM IN EXT jack to an infrared blaster or emitter placed
in front of a source component's IR sensor. In addition, the IR OUT
can be hard-wired to Rotel CD players, DVD players, or tuners with a
compatible connector.
These outputs are used to allow IR signals from the three remote zones
to be sent to the source components, or to pass along IR signals from a
remote in the main room when the sensors on the source components are
blocked by installation in a cabinet.
See your authorized Rotel dealer for information on IR emitters and
repeater systems.

Rear Mini USB Socket

l

Remote IR OUT

p
The Rear USB connector is for connecting to a computer's USB socket.
The RSP-1572 has the ability to learn other component's remote codes
and be programmed to send them via the Remote IR outputs to various
components. This program requires setup on a computer.
For additional information on this feature, please contact your
authorized Rotel dealer.

Computer I/O

u
This Rotel unit can be operated from a computer with audio system control
software from third-party developers. This control is accomplished by
sending operating codes from the computer via a hard-wired RS-232
serial connection. In addition, the RSP-1572 can be updated using
special software from Rotel.
The COMPUTER I/O input provides the necessary network connections
on the rear panel. It accepts standard RJ-45 8-pin modular plugs, such
as those commonly used in 10-BaseT UTP Ethernet cabling.
For additional information on the connections, cabling, software, and
operating codes for computer control or updating of the unit, contact
your authorized Rotel dealer.
21