Roland SP-404SX Manual Del Usuario página 45

No . Type
PHASER
5
Creates modulation by adding a
phase-shifted sound.
TREMOLO/PAN
6
Cyclically varies the volume or
panning.
DISTORTION
7
Intensely distorts the sound.
OVERDRIVE
8
Mildly distorts the sound.
FUZZ
9
Adds overtones and intensely
distorts the sound.
WAH
10
Produces a wah effect.
OCTAVE
11
Adds a pitch at lower octaves.
COMP
12
Makes the sound more consistent.
EQUALIZER
13
Adjusts the volume of each
frequency region.
BIT CRASH
14
Produces an extreme lo-fi effect.
NOISE GEN
15
Applies a lo-fi effect, and also adds
noises such as white noise and
record noise.
VINYL SIM
16
Simulates sound heard from an
analog record.
RADIO TUNING
17
Simulates sound heard from a radio.
SLICER+FLG
18
Repeatedly cuts the sound. A flanger
is added.
RING MOD
19
Gives the sound a metallic character.
CHROMATIC PS
20
A two-voice pitch shifter that
changes the pitch in semitone steps.
PITCH
21
Changes the pitch.
CTRL 1 function (display)
dPt
N
DEPTH ( )
Adjusts the depth of modulation.
d Pt
DEPTH ( )
Adjusts the amount of change in
volume/panning.
d rU
N
DRIVE ( )
Adjusts the degree of distortion.
d rU
N
DRIVE ( )
Adjusts the degree of distortion.
d rU
N
DRIVE ( )
Adjusts the degree of distortion.
PEt
PEAK ( )
Adjusts the width of frequencies to
which effect is applied.
oC 2
-2OCT LEVEL ( )
Adds a pitch two octaves below.
S US
SUSTAIN ( )
Adjusts the depth of the compressor.
Lo
N
LOW ( )
Adjusts the low-frequency volume.
rA t
SAMPLE RATE ( )
Adjusts the sample rate.
UH t
WHITE NOISE ( )
Adjusts the volume of the "hiss"
noise.
rnG
FREQUENCY RANGE ( )
Adjusts the frequency response of
the playback system.
tUn
DETUNE ( )
Adjusts the tuning drift of the radio.
P01 P 16
TIMING PTN ( – ) (*2)
The timing at which the sound is cut.
Frq
N
FREQUENCY ( )
Adjusts the pitch of the metallic
sound.
- C CC
PITCH1 ( – )
Changes pitch 1 in semitone steps
over a +/-1 octave range.
Pit
PITCH ( )
Adjusts the amount of pitch change.
CTRL 2 function (display)
r A t
RATE ( )
Adjusts the speed of modulation.
r A t
RATE ( )
Adjusts the speed of volume/
panning change.
t o n
N
TONE ( )
Adjusts the tone.
t o n
N
TONE ( )
Adjusts the tone.
t o n
N
TONE ( )
Adjusts the tone.
r A t
RATE ( )
Adjust the speed of modulation.
o C 1
-1OCT LEVEL ( )
Adds a pitch one octave below.
A t t r EL
N
ATTACK ( / )
Adjusts the attack. If Limit mode is
on ( r E L ), this adjusts the release.
N id
N
MID ( )
Adjusts the mid-frequency volume.
b it
N
BIT ( )
Adjusts the bit depth.
d i S
DISC NOISE ( )
Adjusts the volume of the "pop"
noise.
no S
NOISE LEVEL ( )
Adjusts the volume of noise.
no S
NOISE LEVEL ( )
Adjusts the volume of noise.
t 3 2 t 1
RATE ( – ) (*1)
Adjusts the length of TIMING PTN.
S En
N
SENS ( )
Adjusts the depth to which the
frequency is modulated.
- C CC
PITCH2 ( – )
Changes pitch 2 in semitone steps
over a +/-1 octave range.
Fd b
N
FEEDBACK ( )
Adjusts the amount of pitch-shifted
sound that is fed back.
CTRL 3 function (display)
NA n
MANUAL ( )
Adjusts the pitch of the effect sound.
t rN PA n
WAVEFORM ( / )
Specifies the volume/panning
modulation curve. Turn knob to left
to vary the volume, or to the right to
vary the panning.
L EU
N
LEVEL ( )
Adjusts the volume.
L EU
N
LEVEL ( )
Adjusts the volume.
L EU
N
LEVEL ( )
Adjusts the volume.
NA n
MANUAL ( )
Adjusts the pitch of the effect sound.
d ir
DIRECT LEVEL ( )
Adjusts the volume of the direct
sound.
L EU
N
LEVEL ( )
Adjusts the volume.
H i
N
HIGH ( )
Adjusts the high-frequency volume.
F Lt
FILTER ( )
Adjusts the filter depth.
HU N
HUM NOISE ( )
Adjusts the volume of the "hum"
noise.
F LU
WOW/FLUTTER ( )
Adjusts the rotational instability of
the analog record.
bA L
BALANCE ( )
Adjusts the volume balance between
the direct sound and effect sound.
F d b
N
FEEDBACK ( )
Adjusts the flanger depth.
bA L
BALANCE ( )
Adjusts the volume balance between
the direct sound and effect sound.
bA L
BALANCE ( )
Adjusts the volume balance between
the direct sound and effect sound.
bA L
BALANCE ( )
Adjusts the volume balance between
the direct sound and effect sound.
43