Changing The Settings; Setting Preferences; About The Auto Standby Function - Pioneer DJM-2000 Manual De Instrucciones

Changing the settings

Setup item button
1

Setting preferences

Settings indicated in italics are the default settings set upon purchase.
Mode Options settings
MIDI
USER SETUP
FADER START
LCD
VERSION No.
SYSTEM
CLUB SETUP
MIC
TOUCH PANEL
FACTORY RESET
1 Changes the MIDI settings of the buttons on the control panel, [FREQUENCY MIX] and [SIDECHAIN REMIX].
2 Changes the MIDI settings for [TYPE A] to [TYPE D] on the MIDI control screen.

About the auto standby function

When [AUTO STANDBY] is set to [ON], the standby mode is set automatically if 4 hours pass with all of the conditions below met.
— That none of this unit's buttons or controls are operated.
— That no audio signals of –10 dB or greater are input to this unit's input terminals.
— That no PRO DJ LINK connections are made.
! The standby mode is canceled when [LIVE SAMPLER (UTILITY, WAKE UP)] is pressed.
24
En
1
Selection item 1 Selection item 2
BUTTON ACTION
1
ZONE1
MIDI CHANNEL
BUTTON ACTION
2
ZONE2
MIDI CHANNEL
RESET
LINK CH1 to CH4
CONTROL CH2, CH3
BACK LIGHT 1, 2, 3, 4, 5
— —
DIGITAL OUT MAX –19 dB, –15 dB, –10 dB,
LEVEL –5 dB
DIGITAL SAMPLING
48 kHz, 96 kHz
RATE
AUTO STANDBY ON, OFF
OUTPUT TO BOOTH
ON, OFF
MONITOR
TALK OVER THRESH- –25 dB, –20 dB, –15 dB,
OLD LEVEL –10 dB
–25 dB, –20 dB, –15 dB,
TALK OVER LEVEL
–10 dB
— —
YES, NO —
1 Press [LIVE SAMPLER (UTILITY, WAKE UP)] for at least 1
seconds.
The [USER SETUP] screen appears.
The [LIVE SAMPLER (UTILITY, WAKE UP)] indicator flashes.
! To display the [CLUB SETUP] screen, first turn this unit's power off, then press
[POWER] while pressing [LIVE SAMPLER (UTILITY, WAKE UP)].
2 Press the setup item button.
The selection items appear.
3 Select the setup item.
Select the item on the touch panel and enter it.
4 Change the item's setting.
Select the item on the touch panel and enter it.
! Press [SAVE] to save the changes to the [CLUB SETUP] screen.
5 Press [EXIT].
The [USER SETUP] screen closes.
! To close the [CLUB SETUP] screen, press [POWER] to turn this unit's power
off.
Selection item 3 Descriptions
TOGGLE
Select the MIDI signal sending method, [TOGGLE] or [TRIGGER].
TRIGGER
1, 2, to 16 Sets the MIDI channel.
TOGGLE
Select the MIDI signal sending method, [TOGGLE] or [TRIGGER].
TRIGGER
1, 2, to 16 Sets the MIDI channel.
Restores the [TYPE A] – [TYPE D] MIDI settings to the default values.
—
[RESET] function is unique to [ZONE2].
Turns the fader start function of the DJ players connected to the
ON, OFF
[LINK] terminals on and off.
Turns the fader start function of the DJ players connected to the
ON, OFF
[CONTROL] terminals on and off.
— Adjusts the touch panel's brightness.
— Displays the DJM-2000's software version.
Adjusts the maximum audio level output from the [DIGITAL OUT]
—
terminal.
— Switches the digital signal sampling rate.
— Turns the auto standby function on and off.
Sets whether or not to output the microphone's audio signals from
—
[BOOTH] terminals.
Sets the talkover sensitivity. The talkover function is activated when
— a sound with a volume above the set volume is input to the micro-
phone.
Sets the attenuation level for the sound other than the microphone's
—
sound when the talkover function is activated.
— The touch panel's calibration is adjusted by pressing [+] in order.
— Restores all the settings to their factory defaults.