Connections; Rear Panel - Pioneer DJM-2000 Manual De Instrucciones

Connections

Be sure to turn off the power and unplug the power cord from the power outlet whenever making or changing connections.
Refer to the operating instructions for the component to be connected.
Connect the power cord after all the connections between devices have been completed.
Be sure to use the included power cord.

Rear Panel

1 2
PHONO
OFF POWER
ON
AC IN
l
1 POWER (page 12)
Turns this unit's power on and off.
2 PHONO (page 7)
Connect to a phono level (MM cartridge) output device. Do not input line level
signals.
3 CD (page 7)
Connect to a DJ player or a line level output component.
4 SIGNAL GND (page 7)
Connect an analog player's ground wire here. This helps reduce noise when
the analog player is connected.
5 CD, DIGITAL (page 12)
Selects the analog signal input terminals (CD) or the digital signal input
terminals (DIGITAL IN).
6 LINE (page 7)
Connect to a cassette deck or a line level output component.
7 CONTROL (page 7)
Connect using a control cord (included with Pioneer DJ players).
8 DIGITAL OUT (page 7)
Outputs the master channel audio signals.
9 DIGITAL IN (page 7)
Connect these to the digital coaxial output terminals on DJ players, etc. The
sound may be momentarily interrupted when the output signal sampling
frequency is switched.
a Kensington security slot
b USB (page 8)
Connect to a computer.
c MIDI OUT (page 7)
Connect this to the MIDI IN terminal on an external MIDI sequencer.
d LINK (page 7)
Connect these to the LINK terminals on Pioneer DJ players or the LAN ports
of computers on which rekordbox is installed (PRO DJ LINK).
e RETURN (page 7)
Connect to the output terminal of an external effector. When the [L (MONO)]
channel only is connected, the [L (MONO)] channel input is simultaneously
input to the [R] channel.
f SEND (page 7)
Connect to the input terminal of an external effector. When the [L (MONO)]
channel only is connected, a monaural audio signal is output.
g BOOTH (page 7)
Output terminals for a booth monitor, compatible with balanced or unbal-
anced output for a TRS connector.
6
En
3 4 5 6 3 7
SIGNAL GND
CH 4 CH 3
CD LINE CD
L L
CONTROL
CD DIGITAL CD DIGITAL
R R
MASTER1 MASTER2 REC OUT
1GND 2HOT
R L
L
3COLD
-6dB -3dB 0dB
R
MASTER
ATT.
k j i
5 8 9
DIGITAL
OUT IN
CH 4 CH 3 CH 2
BOOTH SEND
(TRS)
R L R L(MONO)
h g f
h REC OUT (page 7)
This is an output terminal for recording.
i MASTER2 (page 7)
Connect to a power amplifier, etc.
j MASTER ATT.
Switches the attenuation level of the sound output from the [MASTER1] and
[MASTER2] terminals. Select 0 dB, –3 dB or –6 dB.
k MASTER1 (page 7)
Connect to a power amplifier, etc.
l AC IN
Connect to a power outlet using the included power cord. Wait until all con-
nections between the equipment are completed before connecting the power
cord.
Be sure to use the included power cord.
6 3 7 5 2
CH 2
LINE CD PHONO
L
CONTROL
CD DIGITAL
R
CH 1
CH 3 CH 1 COMPUTER 1
RETURN
R L(MONO)
LINK
CH 4 CH 2 COMPUTER 2
e d
3 4 5 a
SIGNAL GND
CH 1
CD
L
CD DIGITAL
R
MIDI OUT USB
c b