Parts Description; Bench Mounting - Makita DLS211 Manual De Instrucciones

25. When storing the wireless unit, keep it in the
supplied case or a static-free container.
26. Do not insert any devices other than Makita
wireless unit into the slot on the tool.
27. Do not use the tool with the lid of the slot dam-
aged. Water, dust, and dirt come into the slot may
cause malfunction.

PARTS DESCRIPTION

Fig.2
1 Slide pole
5 Sub base
9 Kerf board
13 Blade guard
17 $GMXVWLQJ VFUHZ IRU
ORZHU OLPLW SRVLWLRQ
21 /RFN OHYHU IRU WXUQ EDVH
Fig.3
1 Stopper pin (for carriage
HOHYDWLRQ
5 Switch trigger
9 6ZLWFK IRU ODVHU OLQH
13 Wireless activation
button
17 ƒ DGMXVWLQJ EROW IRU
EHYHO DQJOH
21 Releasing lever (for 48°
EHYHO DQJOH
INSTALLATION
Installing the grip
Screw the threaded shaft of the grip into the turn base.
Fig.4: 1. Grip 2. Turn base
Installing the dust extraction hose
Connect the dust extraction hose to the tool as
illustrated.
0DNH VXUH WKDW WKH HOERZ DQG WKH VOHHYH ¿W SURSHUO\ WR
the ports of the tool.
Fig.5: 1. Dust extraction hose 2. Elbow 3. Sleeve
4. Port
To remove the elbow from the port, pull the elbow while
pressing down the lock button.
Fig.6: 1. Lock button 2. Elbow
2 Stopper pin (for carriage
VOLGLQJ
6 Turn base
10 Blade case
14 .QRE IRU EHYHO DQJOH
18 $GMXVWLQJ EROW IRU PD[L-
PXP FXWWLQJ FDSDFLW\
22 Releasing lever (for turn
EDVH
2 Hose (for dust
H[WUDFWLRQ
6 Lock-off button
10 Battery indicator
14 Wireless activation lamp
18 3RLQWHU IRU EHYHO DQJOH
- -
23 ENGLISH
28. Do not pull and/or twist the lid of the slot more
than necessary. Restore the lid if it comes off
from the tool.
29. Replace the lid of the slot if it is lost or
damaged.
SAVE THESE INSTRUCTIONS.
3 Vertical vise
7 3RLQWHU IRU PLWHU DQJOH
11 $GMXVWLQJ VFUHZ IRU
ODVHU OLQH
15 Hex wrench
19 Stopper arm
23 *ULS IRU WXUQ EDVH
3 Guide fence (upper
IHQFH
7 Hole for padlock
11 Mode indicator
15 Dust bag
19 ƒ DGMXVWLQJ EROW IRU
EHYHO DQJOH
- -

Bench mounting

When the tool is shipped, the handle is locked in the
lowered position by the stopper pin. While lowering the
handle slightly, pull the stopper pin and rotate it 90°.
Fig.7: 1. Locked position 2. Unlocked position
3. Stopper pin
This tool should be bolted with four bolts to a level and
stable surface using the bolt holes provided in the tool's
EDVH 7KLV ZLOO KHOS SUHYHQW WLSSLQJ DQG SRVVLEOH LQMXU\
Fig.8: 1. Bolt
WARNING:
Ensure that the tool will not move
on the supporting surface. Movement of the miter
saw on the supporting surface while cutting may
UHVXOW LQ ORVV RI FRQWURO DQG VHULRXV SHUVRQDO LQMXU\
4 Releasing button (for
ULJKW VLGH EHYHO DQJOH
8 Miter angle scale
12 5DQJH DGMXVWPHQW VFUHZ
IRU ODVHU OLQH
16 Sub fence
20 Battery cartridge
- -
4 Guide fence (lower
IHQFH
8 /LG IRU ZLUHOHVV XQLW
)RU '/6 RQO\
12 Check button
16 Bevel angle scale
20 Latch lever (for bevel
DQJOH
- -