General Power Tool Safety Warnings; Safety Instructions For Mitre Saws - Makita DLS211 Manual De Instrucciones

SAFETY WARNINGS

General power tool safety warnings

WARNING:
Read all safety warnings, instruc-
WLRQV LOOXVWUDWLRQV DQG VSHFL¿FDWLRQV SURYLGHG
with this power tool. Failure to follow all instructions
OLVWHG EHORZ PD\ UHVXOW LQ HOHFWULF VKRFN ¿UH DQGRU
VHULRXV LQMXU\
Save all warnings and instruc-
tions for future reference.
The term "power tool" in the warnings refers to your
PDLQVRSHUDWHG FRUGHG SRZHU WRRO RU EDWWHU\RSHUDWHG
FRUGOHVV SRZHU WRRO

Safety instructions for mitre saws

1. Mitre saws are intended to cut wood or wood-
like products, they cannot be used with abra-
sive cut-off wheels for cutting ferrous material
such as bars, rods, studs, etc. Abrasive dust
causes moving parts such as the lower guard to
MDP 6SDUNV IURP DEUDVLYH FXWWLQJ ZLOO EXUQ WKH
lower guard, the kerf insert and other plastic parts.
2. Use clamps to support the workpiece when-
ever possible. If supporting the workpiece
by hand, you must always keep your hand at
least 100 mm from either side of the saw blade.
Do not use this saw to cut pieces that are too
small to be securely clamped or held by hand.
If your hand is placed too close to the saw blade,
WKHUH LV DQ LQFUHDVHG ULVN RI LQMXU\ IURP EODGH
contact.
3. The workpiece must be stationary and
clamped or held against both the fence and the
table. Do not feed the workpiece into the blade
or cut "freehand" in any way. Unrestrained
or moving workpieces could be thrown at high
VSHHGV FDXVLQJ LQMXU\
4. Push the saw through the workpiece. Do not
pull the saw through the workpiece. To make
a cut, raise the saw head and pull it out over
the workpiece without cutting, start the motor,
press the saw head down and push the saw
through the workpiece. Cutting on the pull stroke
is likely to cause the saw blade to climb on top
of the workpiece and violently throw the blade
assembly towards the operator.
5. Never cross your hand over the intended line
of cutting either in front or behind the saw
blade. Supporting the workpiece "cross handed"
i.e. holding the workpiece to the right of the saw
blade with your left hand or vice versa is very
dangerous.
Fig.1
6. Do not reach behind the fence with either hand
closer than 100 mm from either side of the saw
blade, to remove wood scraps, or for any other
reason while the blade is spinning. The proxim-
ity of the spinning saw blade to your hand may not
EH REYLRXV DQG \RX PD\ EH VHULRXVO\ LQMXUHG
7. Inspect your workpiece before cutting. If the
workpiece is bowed or warped, clamp it with
the outside bowed face toward the fence.
Always make certain that there is no gap
between the workpiece, fence and table along
the line of the cut. Bent or warped workpieces
can twist or shift and may cause binding on the
spinning saw blade while cutting. There should be
QR QDLOV RU IRUHLJQ REMHFWV LQ WKH ZRUNSLHFH
8. Do not use the saw until the table is clear of all
tools, wood scraps, etc., except for the work-
piece. Small debris or loose pieces of wood or
RWKHU REMHFWV WKDW FRQWDFW WKH UHYROYLQJ EODGH FDQ
be thrown with high speed.
9. Cut only one workpiece at a time. Stacked multi-
ple workpieces cannot be adequately clamped or
braced and may bind on the blade or shift during
cutting.
10. Ensure the mitre saw is mounted or placed on
D OHYHO ¿UP ZRUN VXUIDFH EHIRUH XVH A level
DQG ¿UP ZRUN VXUIDFH UHGXFHV WKH ULVN RI WKH PLWUH
saw becoming unstable.
11. Plan your work. Every time you change the
bevel or mitre angle setting, make sure the
adjustable fence is set correctly to support the
workpiece and will not interfere with the blade
or the guarding system. Without turning the tool
"ON" and with no workpiece on the table, move
the saw blade through a complete simulated cut to
assure there will be no interference or danger of
cutting the fence.
12. Provide adequate support such as table exten-
sions, saw horses, etc. for a workpiece that is
wider or longer than the table top. Workpieces
longer or wider than the mitre saw table can tip
if not securely supported. If the cut-off piece or
workpiece tips, it can lift the lower guard or be
thrown by the spinning blade.
13. Do not use another person as a substitute for
a table extension or as additional support.
Unstable support for the workpiece can cause the
blade to bind or the workpiece to shift during the
cutting operation pulling you and the helper into
the spinning blade.
14. The cut-off piece must not be jammed or
pressed by any means against the spinning
saw blade. ,I FRQ¿QHG LH XVLQJ OHQJWK VWRSV WKH
cut-off piece could get wedged against the blade
and thrown violently.
15. $OZD\V XVH D FODPS RU D ¿[WXUH GHVLJQHG WR
properly support round material such as rods
or tubing. Rods have a tendency to roll while
being cut, causing the blade to "bite" and pull the
work with your hand into the blade.
16. Let the blade reach full speed before contact-
ing the workpiece. This will reduce the risk of the
workpiece being thrown.
17. If the workpiece or blade becomes jammed,
turn the mitre saw off. Wait for all moving
parts to stop and disconnect the plug from
the power source and/or remove the battery
pack. Then work to free the jammed material.
&RQWLQXHG VDZLQJ ZLWK D MDPPHG ZRUNSLHFH FRXOG
cause loss of control or damage to the mitre saw.
20 ENGLISH