Carrying Tool - Makita DLS211 Manual De Instrucciones

CAUTION:
Use straight wood of even thick-
ness for the wood facing.
CAUTION:
In order to completely cut through
workpieces with a height of 107 mm to 120 mm, a
wood facing should be used on the guide fence.
The wood facing will space the workpiece away from
the fence allowing the blade to complete a deeper
cut.
NOTICE:
When the wood facing is attached, do
not turn the turn base with the handle lowered.
The blade and/or the wood facing will be damaged.
Use of wood facing helps to assure splinter-free cuts
in workpieces. Attach a wood facing to the guide fence
using the holes in the guide fence and 6 mm screws.
6HH WKH ¿JXUH FRQFHUQLQJ WKH GLPHQVLRQV IRU D VXJ-
gested wood facing.
Fig.64: 1. Hole 2. Over 15 mm 3. Over 270 mm
4. 90 mm 5. 145 mm 6. 19 mm 7. 115 -
120 mm
EXAMPLE When cutting workpieces 115 mm and
120 mm high, use a wood facing with the following
thickness.
Miter angle
0°
Left and Right 45°
Left and Right 60°

Carrying tool

Before carrying the tool, be sure to remove the batteries
and all movable parts of the miter saw are secured.
Always check the following:
• The batteries are removed.
• The carriage is at 0° bevel angle position and
secured.
• The carriage is lowered and locked.
• The carriage is fully slid to the guide fence and
locked.
• The turn base is at the full right miter angle posi-
tion and secured.
• The sub bases are stored and secured.
Carry the tool by holding both sides of the tool base as
VKRZQ LQ WKH ¿JXUH
Fig.65
WARNING:
Stopper pin for carriage elevation
is for carrying and storage purposes only and not
for any cutting operations. The use of the stopper
pin for cutting operations may cause unexpected
movement of the saw blade resulting in kickback and
VHULRXV SHUVRQDO LQMXU\
CAUTION:
Always secure all moving portions
before carrying the tool. If portions of the tool move
or slide while being carried, loss of control or balance
PD\ RFFXU DQG UHVXOW LQ SHUVRQDO LQMXU\
Thickness of wood facing
115 mm 120 mm
20 mm 38 mm
15 mm 25 mm
15 mm 25 mm
WIRELESS ACTIVATION
FUNCTION
For DLS211 only
What you can do with the wireless
activation function
The wireless activation function enables clean and com-
fortable operation. By connecting a supported vacuum
cleaner to the tool, you can run the vacuum cleaner
automatically along with the switch operation of the tool.
Fig.66
To use the wireless activation function, prepare follow-
ing items:
‡ $ ZLUHOHVV XQLW RSWLRQDO DFFHVVRU\
• A vacuum cleaner which supports the wireless
activation function
The overview of the wireless activation function
setting is as follows. Refer to each section for detail
procedures.
1. Installing the wireless unit
2. Tool registration for the vacuum cleaner
3. Starting the wireless activation function
Installing the wireless unit
Optional accessory
CAUTION:
3ODFH WKH WRRO RQ D ÀDW DQG VWDEOH
surface when installing the wireless unit.
NOTICE:
Clean the dust and dirt on the tool before
installing the wireless unit. Dust or dirt may cause
malfunction if it comes into the slot of the wireless unit.
NOTICE:
To prevent the malfunction caused by static,
touch a static discharging material, such as a metal part
of the tool, before picking up the wireless unit.
NOTICE:
When installing the wireless unit, always
be sure that the wireless unit is inserted in the cor-
rect direction and the lid is completely closed.
1. 2SHQ WKH OLG RQ WKH WRRO DV VKRZQ LQ WKH ¿JXUH
Fig.67: 1. Lid
2. Insert the wireless unit to the slot and then close the lid.
:KHQ LQVHUWLQJ WKH ZLUHOHVV XQLW DOLJQ WKH SURMHFWLRQV
with the recessed portions on the slot.
Fig.68: 1. Wireless unit 2. 3URMHFWLRQ 3. Lid
4. Recessed portion
When removing the wireless unit, open the lid slowly. The hooks
on the back of the lid will lift the wireless unit as you pull up the lid.
Fig.69: 1. Wireless unit 2. Hook 3. Lid
After removing the wireless unit, keep it in the supplied
case or a static-free container.
NOTICE:
Always use the hooks on the back of
the lid when removing the wireless unit. If the
hooks do not catch the wireless unit, close the lid
completely and open it slowly again.
34 ENGLISH