Makita DLS211 Manual De Instrucciones página 31

Cutting crown and cove moldings
Crown and cove moldings can be cut on a compound
PLWHU VDZ ZLWK WKH PROGLQJV ODLG ÀDW RQ WKH WXUQ EDVH
There are two common types of crown moldings and
one type of cove moldings; 52/38° wall angle crown
molding, 45° wall angle crown molding and 45° wall
angle cove molding.
Fig.54: 1. 52/38° type crown molding 2. 45° type
crown molding 3. 45° type cove molding
7KHUH DUH FURZQ DQG FRYH PROGLQJ MRLQWV ZKLFK DUH
PDGH WR ¿W ,QVLGH ƒ FRUQHUV D DQG E LQ WKH ¿JXUH
DQG 2XWVLGH ƒ FRUQHUV F DQG G LQ WKH ¿JXUH
(a) (b)
1
1. Inside corner 2. Outside corner
1
(b)
(a)
(b)
(a)
1. Inside corner 2. Outside corner
Measuring
0HDVXUH WKH ZDOO ZLGWK DQG DGMXVW WKH ZLGWK RI WKH
workpiece according to it. Always make sure that width
of the workpiece's wall contact edge is the same as wall
length.
Fig.55: 1. Workpiece 2. Wall width 3. Width of the
workpiece 4. Wall contact edge
Always use several pieces for test cuts to check the
saw angles.
When cutting crown and cove moldings, set the bevel
DQJOH DQG PLWHU DQJOH DV LQGLFDWHG LQ WKH WDEOH $ DQG
position the moldings on the top surface of the saw
EDVH DV LQGLFDWHG LQ WKH WDEOH % 
(c) (d)
2
(b) (a)
(a)
(b)
(d)
2
(c)
(a)
(b)
In the case of left bevel cut
1. Inside corner 2. Outside corner
Table (A)
– Molding
position
in the
¿JXUH
For D
inside
corner
E
For F
outside
G
corner
Table (B)
– Molding
position in
WKH ¿JXUH
For inside
corner
For outside
corner
Example:
In the case of cutting 52/38° type crown molding for
SRVLWLRQ D LQ WKH DERYH ¿JXUH
• Tilt and secure bevel angle setting to 33.9° LEFT.
‡ $GMXVW DQG VHFXUH PLWHU DQJOH VHWWLQJ WR ƒ
RIGHT.
‡ /D\ FURZQ PROGLQJ ZLWK LWV EURDG EDFN KLGGHQ
surface down on the turn base with its CEILING
CONTACT EDGE against the guide fence on the
saw.
‡ 7KH ¿QLVKHG SLHFH WR EH XVHG ZLOO DOZD\V EH RQ
the LEFT side of the blade after the cut has been
made.
31 ENGLISH
(a) (b) (c) (d)
1 2
Bevel angle Miter angle
52/38° 45° type 52/38°
type type
Left Left 30° Right
33.9° 31.6°
Left
31.6°
Right
31.6°
Molding
edge against
guide fence
D Ceiling Finished
contact edge piece will be
should be on the Left
against guide side of blade.
fence.
E Wall contact
edge should
F Finished
be against
piece will be
guide fence.
on the Right
G Ceiling side of blade.
contact edge
should be
against guide
fence.
45° type
Right
35.3°
Left
35.3°
Right
35.3°
Finished
piece