Novoferm iso20-4 Instrucciones De Montaje página 10

Ocultar thumbs Ver también para iso20-4:
Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 44
www.meurer-shop.de
GB
( 10 ) Bolt the track connector 6 using one S6 + S12 to the end
connecting bracket 10 and tighten by hand [
( 11 ) Attach the track connector 6 to the opposite corner con-
necting bracket 10 and bolt both sides tightly using two
each S6 + S12 [
1.30ac,b
( 12 ) Fasten the track connector 6 and horizontal pairs of tracks
14
to the wall or ceiling. Do not yet tighten the nuts and
R/L
bolts
S6
+
S12
[
] (diagonal measurement).
1.30
( 12a ) Wall fastening: Extend anchor track 27 with con-
necting bracket 28 and dowel using S8 + S9 [
( 12b ) Ceiling fastening: Bolt anchor track 27 + connect-
ing bracket 28 using S6 + S12 and dowel using S8 +
S9 [
].
1.30b
Once aligned, tighten the clip plate 29 using S6.
Additionally, fasten the track mounting bracket 9 to the
ceiling, together with the anchor track 27 + connecting
bracket 28 + S6 + S12 + S8 + S9 [
Caution: If the BRH is more than 2126 mm, attach ad-
ditional ceiling mounts to the front of the pair of tracks
14
[
].
1.30d
R/L
Assembly of the garage door leaf
Pre-assembly of the bottom section [
( 13 ) iso20 (top section is at the top of the section set)
Bolt the floor profile 97 using S10 to the bottom section 44
(leave the outer holes free); attach shims U2 on the long
holes [
]. Finish by inserting the rubber end plugs 45
1.35d
[
].
1.35a
Insert the floor seal 47 into the floor track, cut to length
(BRB=L) and insert rubber end plugs 45
using
handle 49
S10 to bottom section
Carefully cut open the protective foil around an end cap
and remove [
]. Attach the logo 58, only on garage
1.35ba,bb
doors without locks [
1.35c
Assembly of the bottom section [
( 14 ) Position the bottom section 44 between the angular frames
1
and place a wedge, approx. 30mm (wood or similar)
R/L
underneath it, to allow subsequent raising of the door leaf.
Guard the bottom section 44 against falling over [
( 14a ) Pull the roller 56 out of the outer hinge 48
pre-assembled roller holder 61, insert it on the other
side of the roller holder 61 and bolt the outer hinge
48
to the bottom section 44 using S10 (M
R/L
Nm) [
1.40a,b - iso20
( 14b ) Pull the roller 56 out of the bottom cable fastener
57
with pre-assembled roller holder 61, insert it on
R/L
the other side of the roller holder 61 and bolt the bot-
tom cable fastener 57
ing 4 x S10 (M
[
]
1.40ad
[
] / [
1.40c,d - iso20
( 14c ) Fold the cable link on the roller holder to ease as-
sembly later 61.
Lock section [
]
1.45
( 15 ) Insert the lock section 67 into the angular frame 1
against falling over and
bolt on the side hinges 48
(M
=10Nm) [
].
1.45a
A
OPTIONAL
-------------------------------------------------------------------------------------
Lock assembly
( 15a ) Press the clip 69 into the appropriate recess on the
outer handle 70 with the long square pin [
Keep these installation, operating, and maintenance instructions in a safe place during the entire service life of the garage door.
www.meurer-shop.de
].
1.30ab
].
on
the
clip
plate
].
1.30c
]
1.35
[
].
Bolt floor
1.35e
R/L
[
].
1.35e
].
]
1.40
1.40
] / [
].
1.40aa,ab - iso45
to the bottom section 44 us-
R/L
by tilting it slightly
=10Nm) and
A
].
1.40ac,ad - iso45
R/L
as with the bottom section 44
(turn the roller) using S10
R/L
1.45b,ba
( 15b ) Assemble the lock set on the lock section 67 as
shown in the exploded view [
plate 72 with cover plate 71 from the outside into the
rectangular hole on the lock section 67 and bolt from
the inside using lock set 73 + 76 S1. Push the outer
handle 70 through the lock 73 and bolt together with
the inside handle 78 from the inside S2. Caution:
The rotating arm 77 (die cast zinc) must point up-
29
wards to the right!
Garage doors without operators
( 15c ) Bolt the catch 79 to the lock section using S10
].
1.30ac
[
1.45cb
( 15d ) Hold the bolt bar 80 to the catch 79 and rotating
arm and shorten to the right length, if necessary, us-
ing a metal saw or power cutter (panel only), leaving
(3-5) mm play, and bolt the catch using S4
( 15e ) Insert the bolt bar 80 into the rotating arm, and both
the catch 79 using S4
---------------------------------------------------------------------------
Middle section(s) [
( 16 ) Using the same procedure as for the bottom 44 and lock
sections 67, bolt the middle section(s) 86 with hinges 48
+ 68 and S10 (M
1
and attach the rollers 56 [
R/L
Top section [
1.50
( 17 ) Bolt the top roller block 90
R/L
using S10 (M
( 17a ) If installing NovoPort, the outer ring on the top roll-
er must be removed on the drive side [
the top roller with your left hand and insert a screw-
driver between the rib and tooth on the roller. Twist
the roller to the right to loosen and remove the outer
ring [
( 17b ) Insert the top section 87 into the angular frames
1
R/L
top roller block 90
and right to the top section 87 using S10
(M
=10Nm). Bolt the side and middle hinges 68 us-
A
ing S10 (M
].
[
1.50b
with
R/L
( 18 ) Adjusting the rollers:
Pull all rollers away from the door leaf in the direction of the
=10
arrows until the door leaf lies flush against the frame seal
A
(distance between section edges and grey part of the frame
seal approx. 1 mm). The rollers must turn easily by hand.
Cable suspension [
( 19 ) Slowly raise the garage door to its end position. Guard
both sides of the door against falling down [
( 20 ) Cable arrangement 12
 Visible area to the left (red), right (black)
Both single cable ends 12 must point outwards [
( 21 ) The double cable end 12 is pushed into the cable mount 4
from the inside and guided downwards [
( 22 ) Making sure they are not crossed over, the single cable
, guard
ends 12 are laid over the deflection pulley 17, which is
bolted to the moulded end piece 16
Guide the two single cable ends 12 into the cable link on
the bottom cable fastener 57
shown [
1.55d
Spring mount [
( 23 ) Attach the long hole on the spring assembly 11 to the
lower spring mount 5 [
].
15 [
].
1.60ab
- 7 -
1.45d
.
]
.
[
]
1.45cb
]
1.50
=10Nm), insert into the angular frames
A
].
1.50c,ca
]
to the top roller holder 88
R/L
=10Nm) [
].
1.50aa
A
].
1.70bb
, guard against falling over, and bolt one each
with top roller holder 88
R/L
=10Nm) to the top and middle section
A
.
]
]
1.55
using S15 [
L/R
until they are in the position
R/L
] (or secure them with safety plugs 22).
]
1.60
] and secure with spring pin
1.60a,aa
Seite 10 von 120
]. Insert the lock
.
[
]
1.45ca
R/L
R/L
]. Grasp
1.70bb
left
R/L
s
.
]
1.55
].
1.55aa,ab
].
1.55b,c
.
]
1.55ba,bb

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Iso45-4

Tabla de contenido