Makita LS1214 Manual De Instrucciones página 19

holder. After using the socket wrench, return it to the
wrench holder.
Installing or removing saw blade
CAUTION:
• Always be sure that the tool is switched off and
unplugged before installing or removing the blade.
• Use only the Makita socket wrench provided to install
or remove the blade. Failure to do so may result in
overtightening or insufficient tightening of the hex bolt.
This could cause a personal injury.
Lock the handle in the raised position by pushing in the
stopper pin. (Fig. 21)
To remove the blade, use the socket wrench to loosen
the hex bolt holding the center cover by turning it coun-
terclockwise. Raise the blade guard and center cover.
(Fig. 22)
Press the shaft lock to lock the spindle and use the
socket wrench to loosen the hex bolt clockwise. Then
remove the hex bolt, outer flange and blade. (Fig. 23)
To install the blade, mount it carefully onto the spindle,
making sure that the direction of the arrow on the surface
of the blade matches the direction of the arrow on the
blade case. Install the outer flange and hex bolt, and then
use the socket wrench to tighten the hex bolt (left-
handed) securely counterclockwise while pressing the
shaft lock. (Fig. 24)
For all countries other than European countries
CAUTION:
• The black ring 25 mm in outer diameter and the silver
ring 25.4 mm in outer diameter are factory-installed as
shown in the figure. When using a blade with 25 mm
hole diameter, replace the silver ring with the black
ring. Before mounting the blade onto the spindle,
always be sure that the correct ring for the arbor hole of
the blade you intend to use is installed between the
inner and outer flanges. (Fig. 25)
For European countries
CAUTION:
• The ring 30 mm in outer diameter is factory-installed
between the inner and outer flanges.
Install the outer flange and hex bolt, and then use the
socket wrench to tighten the hex bolt securely counter-
clockwise while pressing the shaft lock.
Return the blade guard and center cover to its original
position. Then tighten the hex bolt clockwise to secure
the center cover. Release the handle from the raised
position by pulling the stopper pin. Lower the handle to
make sure that the blade guard moves properly. Make
sure shaft lock has released spindle before making cut.
(Fig. 26)
Dust bag (Fig. 27)
The use of the dust bag makes cutting operations clean
and dust collection easy. To attach the dust bag, insert
the dust nozzle into the dust spout on the blade case and
fit the bag's entry port over the dust nozzle.
When the dust bag is about half full, remove the dust bag
from the tool and pull the fastener out. Empty the dust
bag of its contents, tapping it lightly so as to remove par-
ticles adhering to the insides which might hamper further
collection.
NOTE:
If you connect a vacuum cleaner to your saw, more effi-
cient and cleaner operations can be performed.
Securing workpiece
WARNING:
• It is extremely important to always secure the work-
piece properly and tightly with the vise. Failure to do so
can cause the tool to be damaged and/or the work-
piece to be destroyed. PERSONAL INJURY MAY
ALSO RESULT. Also, after a cutting operation, DO
NOT raise the blade until the blade has come to a com-
plete stop.
CAUTION:
• When cutting long workpieces, use supports that are
as high as the top surface level of the turn base. Do not
rely solely on the vertical vise and/ or horizontal vise to
secure the workpiece.
Thin material tends to sag. Support workpiece over its
entire length to avoid blade pinch and possible KICK-
BACK. (Fig. 28)
Sub-fence
This tool is equipped with the sub-fence which should
ordinarily be positioned as shown in Fig. 29.
However, when performing left bevel cuts, set it to the left
position as shown in Fig. 30.
CAUTION:
• When performing left bevel cuts, flip the fence over to
the left position as shown in Fig. 30. Otherwise, it will
contact the blade or a part of the tool, causing possible
serious injury to the operator.
Sub-fence R (Fig. 31)
The sub-fence R can be installed on the right side of the
guide fence. Insert the rods of the sub-fence R into the
holes in the guide fence. Tighten the screws which come
with the sub-fence R to secure the sub-fence R.
CAUTION:
• When performing right bevel cuts, never use the sub-
fence R. It will contact the blade or a part of the tool,
causing a serious injury to operator.
Vertical vise (Fig. 32 & 33)
The vertical vise can be installed in two positions on
either the left or right side of the guide fence. Insert the
vise rod into the hole in the guide fence and tighten the
screw on the back of the guide fence to secure the vise
rod.
The vertical vise can also be secured to the rod on the
right side of the subfence R.
Position the vise arm according to the thickness and
shape of the workpiece and secure the vise arm by tight-
ening the screw. If the screw to secure the vise arm con-
tacts the guide fence, install the screw on the opposite
side of vise arm. Make sure that no part of the tool con-
tacts the vise when lowering the handle fully and pulling
or pushing the carriage all the way. If some part contacts
the vise, re-position the vise.
Press the workpiece flat against the guide fence and the
turn base. Position the workpiece at the desired cutting
position and secure it firmly by tightening the vise knob.
CAUTION:
• The workpiece must be secured firmly against the turn
base and guide fence with the vise during all opera-
tions.
19